MC44608P100 ON Semiconductor, MC44608P100 Datasheet
MC44608P100
Specifications of MC44608P100
Related parts for MC44608P100
MC44608P100 Summary of contents
Page 1
... Demag sense Control Input 3 (Top View) GND 4 (Top View) AWL = Manufacturing Code YYWW = Date Code ORDERING INFORMATION Switching Device Frequency MC44608P40 40 kHz MC44608P75 75 kHz MC44608P100 100 kHz Driver Package Shipping Plastic 50/Rail DIP−8 Plastic 50/Rail DIP−8 Plastic 50/Rail DIP−8 ...
Page 2
DMG + − /20 mV Demag Logic Latched off Output Phase Start−up Start−up Phase Switching m Phase 200 A Phase & Stand−by Stand−by Management OC Leading Edge Output Blanking 2 Isense MAXIMUM RATINGS Rating Total ...
Page 3
... Leading Edge Blanking + Propagation Delay Leading Edge Blanking + Propagation Delay Leading Edge Blanking + Propagation Delay OSCILLATOR SECTION Normal Operation Frequency MC44608P40 Normal Operation Frequency MC44608P75 Normal Operation Frequency MC44608P100 Maximum Duty Cycle @ osc OVERVOLTAGE SECTION Quick OVP Input Filtering (R = 100 kW) ...
Page 4
... V cl−neg−dem dem−NM MC44608P40 MC44608P75 MC44608P100 stup−uvlo1 H uvlo1−uvlo2 = 100 V) and i MC44608P40 MC44608P75 MC44608P100 I CC−latch d http://onsemi.com 4 = − +85 C unless otherwise A Min Typ Max dmg−th H − 30 − dmg − 300 − −0.6 − − dem−lb − ...
Page 5
Pin Name The Demag pin offers 3 different functions: Zero voltage crossing detection (50 mV current detection 1 Demag and 120 mA current detection. The 24 mA level is used to detect the secondary reconfiguration status and the ...
Page 6
In stand−by mode, this current can be lowered as due to the activation of a 200 mA current source (kW) + Ipk max *stby R sense (W) Switching Phase m 200 A & Isense ...
Page 7
OSC 4 V Vcont 2.4 V Clock DMG Iprim Figure 6. The OSC and Clock signals are provided according to the Figure 6. The Clock signals correspond to the CT capacitor discharge. The bottom curve represents the current flowing in ...
Page 8
Overload In the hiccup mode the 3 distinct phases are described as follows (refer to Figure 7): The SWITCHING PHASE: The SMPS output is low and the regulation block reacts by increasing the ON time (dmax = 80%). The ...
Page 9
EQUATION 1 Start−up Phase Duration: (V stup * UVLO2) C Vcc t start– stup where the start−up current flowing through V stup C is the V capacitor value Vcc CC EQUATION 2 Switching Phase Duration: (V ...
Page 10
EQUATION ccS Stup I stup EQUATION stup where ccs stup ...
Page 11
Pin6 V Voltage (V) CC Figure 9. Output Switching Speed − 0.0 0.5 ...
Page 12
C 10.00 9. 6.00 5.00 0 100 200 Vi Pin8 Voltage (Vi) Figure 15. High Voltage Current Source The data in Figure 16 corresponds to the waveform in Figure 17. The Figure ...
Page 13
The Figure 19 represents a complete power supply using the secondary reconfiguration. The specification is as follows: Input source: 3 Outputs Output power Stand−by mode R F6 47288900 FI RFI WIDE C1 FILTER MAINS 100 nF C3 D1, D2, D3, ...
Page 14
The secondary reconfiguration is activated by the mP through the switch. The dV/dt appearing on the high voltage winding (pins 14 of the transformer) at every TMOS switch off, produces a current spike through the series RC network R7, C17. ...
Page 15
F −A− NOTE 2 C −T− N SEATING PLANE 0.13 (0.005) M MC44608 PACKAGE DIMENSIONS PDIP−8 P SUFFIX PLASTIC PACKAGE CASE 626−05 ISSUE ...
Page 16
... Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com MC44608 N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 16 ON Semiconductor Website: http://onsemi ...