FAN2106MPX Fairchild Semiconductor, FAN2106MPX Datasheet - Page 3

• Manufacturer Part Number: FAN2106MPX
• Description: IC BUCK SYNC ADJ 6A 25MLP
• Manufacturer: Fairchild Semiconductor
• Series: TinyBuck™r
• Type: Step-Down (Buck)r

Specifications of FAN2106MPX

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 3 ~ 21 V
• Current - Output: 6A
• Frequency - Switching: 300kHz ~ 600kHz
• Voltage - Input: 3 ~ 24 V
• Operating Temperature: -10°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 25-MLP
• Power - Output: 2.8W
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 10 C to + 85 C
• Output Voltage: 0.4 V to 3.2 V
• Primary Input Voltage: 24V
• No. Of Outputs: 1
• Output Current: 6A
• No. Of Pins: 25
• Filter Terminals: SMD
• Output Current Max: 6A
• Rohs Compliant: Yes
• Input Voltage Primary Max: 24V
• For Use With: FEB167 - BOARD EVAL FOR FAN2106
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: FAN2106MPXTR

© 2009 Fairchild Semiconductor Corporation
FAN2106 • Rev. 1.1.0
Pin Configuration
Pin Definitions
P3, 21-23
P1, 6-12
P2, 2-5
Pin #
13
14
15
16
17
18
19
20
24
25
1
PGOOD
Name
COMP
PGND
BOOT
AGND
RAMP
VCC
ILIM
R(T)
SW
VIN
NC
EN
FB
Description
Switching Node. Junction of high-side and low-side MOSFETs.
Power Input Voltage. Connect to the main input power source.
Power Ground. Power return and Q2 source.
High-Side Drive BOOT Voltage. Connect through capacitor (C
includes an internal synchronous bootstrap diode to recharge the capacitor on this pin to
V
Power-Good Flag. An open-drain output that pulls LOW when FB is outside the limits
specified in electrical specs. PGOOD does not assert HIGH until the fault latch is enabled.
ENABLE. Enables operation when pulled to logic HIGH or left open. Toggling EN resets the
regulator after a latched fault condition. This input has an internal pull-up when the IC is
functioning normally. When a latched fault occurs, EN is discharged by a current sink.
Input Bias Supply for IC. The IC’s logic and analog circuitry are powered from this pin.
This pin should be decoupled to AGND through a >1µF X5R/X7R capacitor.
Analog Ground. The signal ground for the IC. All internal control voltages are referred to
this pin. Tie this pin to the ground island/plane through the lowest impedance connection.
Current Limit. A resistor (R
limit trip threshold lower than the default setting.
Oscillator Frequency. A resistor (R
frequency.
Output Voltage Feedback. Connect through a resistor divider to the output voltage.
Compensation. Error amplifier output. Connect the external compensation network
between this pin and FB.
No Connect. This pin is not used.
Ramp Amplitude. A resistor (R
amplitude and provides voltage feedforward functionality.
CC
when SW is LOW.
Figure 3. MLP 5x6mm Pin Configuration (Bottom View)
ILIM
) from this pin to AGND can be used to program the current-
RAMP
3
) connected from this pin to VIN sets the ramp
T
) from this pin to AGND sets the PWM switching
BOOT
) to SW. The IC
www.fairchildsemi.com