LM2576T-ADJG ON Semiconductor, LM2576T-ADJG Datasheet - Page 15

IC REG SW 3A ADJ STEPDWN TO220-5

LM2576T-ADJG

Manufacturer Part Number
LM2576T-ADJG
Description
IC REG SW 3A ADJ STEPDWN TO220-5
Manufacturer
ON Semiconductor
Type
Step-Down (Buck)r
Datasheet

Specifications of LM2576T-ADJG

Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.23 ~ 37 V
Current - Output
3A
Frequency - Switching
52kHz
Voltage - Input
7 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Output Voltage
1.23 V to 37 V
Output Current
3 A
Input Voltage
4.75 V to 40 V
Switching Frequency
52 KHz
Operating Temperature Range
- 40 C to + 125 C
Mounting Style
Through Hole
Duty Cycle (max)
98 %
Primary Input Voltage
40V
No. Of Outputs
1
No. Of Pins
5
Filter Terminals
Through Hole
Rohs Compliant
Yes
Dc
0739
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
LM2576T-ADJGOS

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM2576T-ADJG
Manufacturer:
ON
Quantity:
250
Part Number:
LM2576T-ADJG
Manufacturer:
ONSEMICONDUCTOR
Quantity:
1 324
Part Number:
LM2576T-ADJG
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
LM2576T-ADJG
Manufacturer:
ON
Quantity:
17 112
Part Number:
LM2576T-ADJG
0
Company:
Part Number:
LM2576T-ADJG
Quantity:
8 000
Input Capacitor (C
The Input Capacitor Should Have a Low ESR
ESR (Equivalent Series Resistance) aluminium or solid
tantalum bypass capacitor is needed between the input pin
and the ground pin, to prevent large voltage transients from
appearing at the input. It must be located near the regulator
and use short leads. With most electrolytic capacitors, the
capacitance value decreases and the ESR increases with
lower temperatures. For reliable operation in temperatures
below −25°C larger values of the input capacitor may be
needed. Also paralleling a ceramic or solid tantalum
capacitor will increase the regulator stability at cold
temperatures.
RMS Current Rating of C
current rating. Capacitors that are physically large and have
large surface area will typically have higher RMS current
ratings. For a given capacitor value, a higher voltage
electrolytic capacitor will be physically larger than a lower
voltage capacitor, and thus be able to dissipate more heat to
the surrounding air, and therefore will have a higher RMS
current rating. The consequence of operating an electrolytic
capacitor beyond the RMS current rating is a shortened
operating life. In order to assure maximum capacitor
operating lifetime, the capacitor’s RMS ripple current rating
should be:
where d is the duty cycle, for a buck regulator
and d +
For stable operation of the switch mode converter a low
The important parameter of the input capacitor is the RMS
t on
T
+
|V out | ) V
I
in
rms
Table 3. Example of Several Inductor Manufacturers Phone/Fax Numbers
|V out |
)
Pulse Engineering, Inc.
Pulse Engineering, Inc. Europe
Renco Electronics, Inc.
Tech 39
Schott Corporation
d +
> 1.2 x d x I
in
t on
T
in
+
for a buck * boost regulator.
V out
V
Load
in
EXTERNAL COMPONENTS
http://onsemi.com
LM2576
15
Phone
Fax
Phone
Fax
Phone
Fax
Phone
Fax
Phone
Fax
Output Capacitor (C
output capacitors are recommended. An output capacitor
has two main functions: it filters the output and provides
regulator loop stability. The ESR of the output capacitor and
the peak−to−peak value of the inductor ripple current are the
main factors contributing to the output ripple voltage value.
Standard aluminium electrolytics could be adequate for
some applications but for quality design, low ESR types are
recommended.
related to many factors such as the capacitance value, the
voltage rating, the physical size and the type of construction.
In most cases, the higher voltage electrolytic capacitors have
lower ESR value. Often capacitors with much higher
voltage ratings may be needed to provide low ESR values
that, are required for low output ripple voltage.
The Output Capacitor Requires an ESR Value
That Has an Upper and Lower Limit
output ripple voltage, typically 1% to 2% of the output
voltage. But if the selected capacitor’s ESR is extremely low
(below 0.05 W), there is a possibility of an unstable feedback
loop, resulting in oscillation at the output. This situation can
occur when a tantalum capacitor, that can have a very low
ESR, is used as the only output capacitor.
At Low Temperatures, Put in Parallel Aluminium
Electrolytic Capacitors with Tantalum Capacitors
temperatures below −25°C. The ESR rises dramatically at
cold temperatures and typically rises 3 times at −25°C and
as much as 10 times at −40°C. Solid tantalum capacitors
have much better ESR spec at cold temperatures and are
recommended for temperatures below −25°C. They can be
also used in parallel with aluminium electrolytics. The value
of the tantalum capacitor should be about 10% or 20% of the
total capacitance. The output capacitor should have at least
50% higher RMS ripple current rating at 52 kHz than the
peak−to−peak inductor ripple current.
For low output ripple voltage and good stability, low ESR
An aluminium electrolytic capacitor’s ESR value is
As mentioned above, a low ESR value is needed for low
Electrolytic capacitors are not recommended for
+ 1−619−674−8100
+ 1−619−674−8262
+ 353−9324−107
+ 353−9324−459
+ 1−516−645−5828
+ 1−516−586−5562
+ 33−1−4115−1681
+ 33−1−4709−5051
+ 1−612−475−1173
+ 1−612−475−1786
out
)

Related parts for LM2576T-ADJG