RF600D RF Solutions, RF600D Datasheet
RF600D
Specifications of RF600D
Available stocks
Related parts for RF600D
RF600D Summary of contents
Page 1
... DS600-10 March ‘06 Description The RF Solutions RF600E, & RF600D are easy to use encoder and decoder I/C’s. They have been designed to achieve the maximum possible range from any radio / Infra Red transmitter receiver set. Unlike other encoder /decoder devices the RF600E/600D ...
Page 2
... This provides a bespoke remote chipset for OEM applications. Please contact our sales department for further information. DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 2 ...
Page 3
... Not that a circuit constructed using AM radio modules does not need to have transistor BC848, resistor 10K or 2k2 Pull up resistor fitted. DS600-10 March ‘06 Description Vcc Transmit LED Vcc LED RF600E 3 6 BC848 S2 DO 10K GND ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Pull Up Resistor 2K2 RF Transmitte r Serial Data Output Page 3 ...
Page 4
... RF600E encoder is transmitting). EEPROM storage When the RF600D is used in its internal eeprom mode it can learn the identity transmitters. If required, an external 96C76 eeprom can be connected as shown below and this will be automatically detected by the device and will allow the decoder to learn the identity transmitters. ...
Page 5
... If S1 and S2 are pressed together: 2345678C (2345678c if the battery voltage in the transmitter is low pressed: 2345678H (2345678h if the battery voltage in the transmitter is low) DS600-10 March ‘ A( $0A 10 bytes of data transmitted ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Line feed (last character) Carriage return Transmitter button information with battery status Transmitter serial number Page 5 ...
Page 6
... If the data mark selection is pull-down then the RF600D will be set to receive Sync Low AM data. If the data mark selection is pull-up then the RF600D will be set to receive Sync High FM and IR data. DS600-10 March ‘06 ...
Page 7
... After the status LED has stopped flashing the transmitter has been successfully taught to the decoder 6. This transmitter will now operate the system unique encoders may be learnt to each RF600D. This can be extended to 48 encoders with the use of the 93C76 EEPROM. Erase Operation using momentary push switch (As application circuit) To completely erase all transmitter data, press and hold the learn switch on the decoder for 8 seconds ...
Page 8
... Incoming data mark selection on pin 7 MUST resistor (typically 22K) to either +5 or ground and NOT by a direct connection. 7. The RF/IR data input (pin 9) must valid logic level at all times. In sleep mode, if this input is allowed to float then significant device current may flow. DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 8 ...
Page 9
... Encoder / Decoder Chipset RF Evaluation Boards, RF600D Application Circuit – Stand Alone operation Status LED Vcc Learn Switch RF Receiver This circuit provides a complete decoding solution capable of learning unique encoders DS600-10 March ‘06 Vcc 1KΩ 13 Sleep L 12 Option LKIN Link M 10 LRN 1KΩ ...
Page 10
... Encoder / Decoder Chipset RF Evaluation Boards, RF600D Application Circuit – With External EEPROM Vcc RF Receiver This circuit provides a complete decoding solution capable of learning unique encoders A complete ‘ready to operate’ board using this circuit is available please see SA123 later in this datasheet DS600-10 March ‘06 Vcc 1KΩ ...
Page 11
... LED sink current Momentary Output min Time of operation RF600E / 600D System Characteristics Electrical Characteristics Time from RF600E input operation to RF600D Output asserted Time from RF600E input released to RF600D Output released DS600-10 March ‘06 Rating -0.3 to 6.9 -0.3 to VDD + 0.3 -0.3 to VDD+ 0.3 ...
Page 12
... Pin Descriptions Pin Name Number 1 Vcc Vss DS600-10 March ‘06 Description Encoder IC Encoder IC Decoder IC Decoder IC Decoder IC Serial output only Decoder IC Serial Output only RF600D 8 Pin version RF600D8 Input / Output? In Positive supply voltage connection Out Serial Data output - No connection In ...
Page 13
... Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 13 ...
Page 14
... Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 14 ...
Page 15
... Encoder / Decoder Chipset RF Evaluation Boards, DS600-10 March ‘06 ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 15 ...
Page 16
... Use of R.F. Solutions as critical components in life support systems is not authorised except with express written approval from R.F.Solutions Ltd. DS600-10 March ‘ Solutions Ltd., Unit 21, Cliffe Industrial Estate, Lewes, E Sussex, BN8 6JL, England Fax +44 (0)1273 480 661 Email sales@rfsolutions.co.uk http://www.rfsolutions.co. Solutions is a member of the Low Power Radio Association. ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 16 ...
Page 17
... Transmitter 1 AM-110C3-433 2 AM-110C3-433 2 AM-110C3-433 4 102C4-433F RFEVAL3 consists a Receiver decoder board only with the RF600D, this requires the relevant RF Receiver module and antenna to generate a complete receiver Decoder (this is an RF600D design) Contents List: Item Part No 1 SA123 2 BATT-PP3 DS600-10 March ‘06 Description pocket keyfob transmitter433MHz, 3 Switch Transmitter/Encoder 433 ...
Page 18
... EEPROM memory 96C76. Learn switch. Learn LED. Alternately the RF600D8 decoder can be fitted in place of the RF600D device. This decoder outputs a serial data stream for any KeeLoq decoder from which it receives data without the requirement to first learn the identity of the encoder. Digital output area. ...
Page 19
... Irrespective of how many modules are fitted, it will be necessary to connect the +5 volt and data lines of one module using the link options filed on the PCB important that only one pair of links be made at DS600-10 March ‘06 (M5) (SW2) (LED7) (LED8, 9, 10) (U5) (LED11) ©2004 Reg. No. 227 4001, ENGLAND RF600E RF600D Page 19 ...
Page 20
... The RF600D chip can decode signals from either the radio modules or the IR receiver device and option field OPT1 allows the selection of the desired input. Input Radio data IR data Output function. The RF600D chip has 4 data outputs and these can operate as either all latched or all momentary. Output mode Latch all Momentary all DS600-10 March ‘06 Reference ...
Page 21
... When the bit stream is generated by the KeeLoq chip a 4 element sync pattern is inserted to allow the RF600D chip to detect the end of the ‘01’ run-in part of the stream and the start of the data. At the output terminal of the KeeLoq chip this 4 element sync pattern consists of 4 elements of data ‘0’ and if the radio or IR data path does not invert the data then we would see this 4 element pattern in the data stream at the input terminal of the RF600D chip. In this case we would say that the ‘ ...
Page 22
... Schmitt trigger data slicer encoder is activated and pointed at the detector then the output waveform will be of +ve mark and can be coupled to the RF600D subsystem by setting the input selector OPT1 and the mark selector OPT3, to FM. ...
Page 23
... Configuring the outputs to operate with Transmitter Encoders The principle of operation is as previously described in the operation of the RF600D. Note that the on board RF600D will only operate the digital outputs of ‘pre-learnt’ transmitter encoders. Upto 48 unique transmitters may be learnt. The Serial output will be valid whenever a transmitter encoder is operated within range of the receiver as long as the transmitter encoder has a matching Manufacturers Key ...
Page 24
... Encoder / Decoder Chipset RF Evaluation Boards, Select OK. HyperTerminal is now configured correctly for use with the RF600E/RF600D chip set. Application Example : Leisure Centre Access Control A Leisure Centre uses an electric gate access control to its members. Member is provided with a keyfob and when entering the centre, uses the keyfob to open the gate. ...