HCPL-0900 Avago Technologies US Inc., HCPL-0900 Datasheet - Page 12

ISOLATOR DIG 100MBD 1CH 8-SOIC

HCPL-0900

Manufacturer Part Number
HCPL-0900
Description
ISOLATOR DIG 100MBD 1CH 8-SOIC
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of HCPL-0900

Propagation Delay
12ns
Inputs - Side 1/side 2
1/0
Number Of Channels
1
Isolation Rating
2500Vrms
Voltage - Supply
3 V ~ 5.5 V
Data Rate
100MBd
Output Type
Tri-State
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 100°C
No. Of Channels
1
Isolation Voltage
2.5kV
Optocoupler Output Type
Logic Gate
Input Current
10µA
Output Voltage
5V
Opto Case Style
SOIC
No. Of Pins
8
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
516-1150-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HCPL-0900
Manufacturer:
AGILENT
Quantity:
20 000
Part Number:
HCPL-0900-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-0900-000E/HCPL0900
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Applications Information
Power Consumption
The HCPL-90xx and HCPL-09xx CMOS digital isolators
achieves low power consumption from the manner by
which they transmit data across isolation barrier. By
detecting the edge transitions of the input logic signal
and converting this to a narrow current pulse, which
drives the isolation barrier, the isolator then latches the
input logic state in the output latch. Since the current
pulses are narrow, about 2.5 ns wide, the power consump-
tion is independent of mark-to-space ratio and solely
dependent on frequency.
The approximate power supply current per channel is:
I(Input) = 40(f/fmax)(1/4) mA
where f = operating frequency, fmax = 50 MHz.
Signal Status on Start-up and Shut Down
To minimize power dissipation, the input signals to the
channels of HCPL-90xx and HCPL-09xx digital isolators
are differentiated and then latched on the output side of
the isolation barrier to reconstruct the signal. This could
result in an ambiguous output state depending on power
up, shutdown and power loss sequencing. Therefore, the
designer should consider the inclusion of an initializa-
tion signal in this start-up circuit. Initialization consists of
toggling the input either high then low or low then high.
V
Figure 1. Functional Diagram of Single Channel HCPL-0900 or HCPL-0900.
GND
Figure 2. Recommended Printed Circuit Board Layout.
12
V
DD1
IN
DD1
Note: C1, C2 = 47 nF ceramic capacitors
IN
1
1
1
GND
C1
1
NC
1
2
3
4
C1
8
7
6
5
V
OE
GND
C2
2
V
OUT
DD2
1
V
OE
C2
Bypassing and PC Board Layout
The HCPL-90xx and HCPL-09xx digital isolators are
extremely easy to use. No external interface circuitry is
required because the isolators use high-speed CMOS IC
technology allowing CMOS logic to be connected directly
to the inputs and outputs. As shown in Figure 1, the only
external components required for proper operation are
two 47 nF ceramic capacitors for decoupling the power
supplies. For each capacitor, the total lead length between
both ends of the capacitor and the power-supply pins
should not exceed 20 mm. Figure 2 illustrates the recom-
mended printed circuit board layout for the HCPL-9000
or HCPL-0900. For data rates in excess of 10MBd, use of
ground planes for both GND
mended.
V
OUT
GND
DD2
1
2
1
and GND
2
is highly recom-

Related parts for HCPL-0900