HCPL-2530-000E Avago Technologies US Inc., HCPL-2530-000E Datasheet - Page 8

• Manufacturer Part Number: HCPL-2530-000E
• Description: OPTOCOUPLER T-OUT 2CH 1MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-2530-000E

• Input Type: DC
• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 8mA
• Data Rate: 1MBd
• Propagation Delay High - Low @ If: 200ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Output Device: Transistor With Base
• Configuration: 2 Channel
• Current Transfer Ratio: 50 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 45 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 55 C
• No. Of Channels: 2
• Optocoupler Output Type: Phototransistor
• Input Current: 16mA
• Output Voltage: 20V
• Opto Case Style: DIP
• No. Of Pins: 8
• Ctr Min: 7%
• Common Mode Ratio: 1k
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1659-5

IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (Option 060)
Description
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
Input to Output Test Voltage, Method a*
Highest Allowable Overvoltage
(Transient Overvoltage, t
Safety Limiting Values
(Maximum values allowed in the event of a failure.)
Insulation Resistance at T
*
** Refer to the following figure for dependence of P
Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.
8
for rated mains voltage ≤ 150 V rms
for rated mains voltage ≤ 300 V rms
for rated mains voltage ≤ 600 V rms
V
with t
V
t
Case Temperature
Input Current**
Output Power**
Refer to the optocoupler section of the Isolation and Control Components Designer's Catalog, under Product Safety Regulations section,
IEC/EN/DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles.
m
IORM
IORM
= 60 sec, Partial Discharge < 5 pC
m
x 1.875 = V
x 1.5 = V
= 1 sec, Partial Discharge < 5 pC
800
700
600
500
400
300
200
100
0
PR
0
, Type and Sample Test,
PR
T
, 100% Production Test
25
S
ini
– CASE TEMPERATURE – °C
S
, V
50
= 10 sec)
IO
= 500 V
75 100
P
I
S
S
(mA)
(mW)
125
150 175
S
and I
S
200
on ambient temperature.
Symbol
V
V
V
V
T
I
P
R
S,INPUT
S
IORM
PR
PR
IOTM
S,OUTPUT
S
Characteristic
HCPL-
2530/2531/4534
I-IV
I-III
55/100/21
2
630
1181
945
6000
175
230
600
> 10
9
HCPL-
0530/0531/0534
I-IV
I-III
I-II
55/100/21
2
567
1050
840
4000
150
230
600
> 10
9
Unit
V
V
V
V
˚C
mA
mW
:
peak
peak
peak
peak