OPTOCOUPLER GATE DRIVE 0.6A 8DIP

HCPL-3150

Manufacturer Part NumberHCPL-3150
DescriptionOPTOCOUPLER GATE DRIVE 0.6A 8DIP
ManufacturerAvago Technologies US Inc.
HCPL-3150 datasheet
 

Specifications of HCPL-3150

Voltage - Isolation3750VrmsNumber Of Channels1, Unidirectional
Current - Output / Channel600mAPropagation Delay High - Low @ If300ns @ 7mA ~ 16mA
Current - Dc Forward (if)25mAInput TypeDC
Output TypeOpen CollectorMounting TypeThrough Hole
Package / Case8-DIP (0.300", 7.62mm)No. Of Channels1
Isolation Voltage3.75kVOptocoupler Output TypeGate Drive
Input Current16mAOutput Voltage30V
Opto Case StyleDIPNo. Of Pins8
Propagation Delay Low-high0.5µsCommon Mode Voltage Vcm1500V
Lead Free Status / RoHS StatusContains lead / RoHS non-compliantOther names516-1125-5
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
21
Page 1/21

Download datasheet (212Kb)Embed
Next
HCPL-3150 (Single Channel), HCPL-315J (Dual Channel)
0.5 Amp Output Current IGBT Gate Drive Optocoupler
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-315X consists of an LED optically coupled
to an integrated circuit with a power output stage. This
optocoupler is ideally suited for driving power IGBTs and
MOSFETs used in motor control inverter applications.
The high operating voltage range of the output stage
provides the drive voltages required by gate controlled
devices. The voltage and current supplied by this opto-
coupler makes it ideally suited for directly driving IGBTs
with ratings up to 1200 V/50 A. For IGBTs with higher rat-
ings, the HCPL-3150/315J can be used to drive a discrete
power stage which drives the IGBT gate.
Applications
x Isolated IGBT/MOSFET gate drive
x AC and brushless dc motor drives
x Industrial inverters
x Switch Mode Power Supplies (SMPS)
x Uninterruptable Power Supplies (UPS)
Functional Diagram
N/C
1
8
V
CC
V
ANODE
2
7
O
CATHODE
3
6
V
O
N/C
4
5
V
EE
SHIELD
HCPL-3150
A 0.1 μF bypass capacitor must be connected between the V
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Features
x 0.6A maximum peak output current
x 0.5 A minimum peak output current
x 15 kV/μs minimum Common Mode Rejection (CMR)
at V
CM
x 1.0V maximum low level output voltage (V
eliminates need for negative gate drive
x I
= 5 mA maximum supply current
CC
x Under Voltage Lock-Out protection (UVLO) with
hysteresis
x Wide operating V
x 0.5 μs maximum propagation delay
x +/– 0.35 μs maximum delay between devices/
channels
x Industrial temperature range: -40°C to 100°C
x HCPL-315J: channel one to channel two output
isolation = 1500 Vrms/1 min.
x Safety and regulatory approval:
UL recognized (UL1577),
3750 Vrms/1 min (HCPL-3150)
5000 Vrms/1 min (HCPL-315J)
IEC/EN/DIN EN 60747-5-2 approved
V
IORM
V
IORM
N/C
1
16
V
CC
V
ANODE
2
15
O
CATHODE
3
14
V
EE
SHIELD
V
ANODE
6
11
CC
CATHODE
7
10
V
O
N/C
8
9
V
EE
SHIELD
HCPL-315J
and V
pins for each channel.
CC
EE
= 1500 V
range: 15 to 30 volts
CC
= 630 V
(HCPL-3150 option 060 only)
peak
= 1230 V
(HCPL-315J) CSA certified
peak
TRUTH TABLE
V
- V
V
- V
CC
EE
CC
EE
“Positive Going”
“Negative-Going”
LED
(i.e., Turn-On)
(i.e., Turn-Off)
OFF
0 - 30 V
0 - 30 V
ON
0 - 11 V
0 - 9.5 V
ON
11 - 13.5 V
9.5 - 12 V
ON
13.5 - 30 V
12 - 30 V
)
OL
V
O
LOW
LOW
TRANSITION
HIGH

HCPL-3150 Summary of contents

  • Page 1

    ... The voltage and current supplied by this opto- coupler makes it ideally suited for directly driving IGBTs with ratings up to 1200 V/50 A. For IGBTs with higher rat- ings, the HCPL-3150/315J can be used to drive a discrete power stage which drives the IGBT gate. Applications ...

  • Page 2

    ... Current CMR 15 kV/μs (minimum) UVLO Yes Fault Status Ordering Information HCPL-3150 is UL Recognized with 3750 Vrms for 1 minute per UL1577. HCPL-315J is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Part RoHS Non RoHS Number Compliant Compliant -000E ...

  • Page 3

    Package Outline Drawings Standard DIP Package 9.40 (0.370) 9.90 (0.390 3150 Z YYWW PIN ONE 1.78 (0.070) MAX. 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) PIN ONE 2.92 (0.115) ...

  • Page 4

    ... Lead Surface Mount 10.36 ± 0.20 HCPL-315J (0.408 ± 0.008 VIEW FROM PIN 16 9° VIEW FROM PIN 1 (0.018) 0.457 (0.406 ± 0.007) 10.31 ± 0.18 4 LAND PATTERN RECOMMENDATION (0.295 ± 0.004) 7.49 ± 0. (0.025) 0.64 (0.004 – 0.011) 0.10 – 0.30 (0.345 ± ...

  • Page 5

    ... Recommended Pb-Free IR Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The HCPL-3150 and HCPL-315J have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324 ...

  • Page 6

    ... Output Power Dissipation Total Power Dissipation Lead Solder Temperature Solder Reflow Temperature Profile Recommended Operating Conditions Parameter Symbol Power Supply Voltage (V Input Current (ON) Input Voltage (OFF) Operating Temperature 6 HCPL-3150 HCPL-315J 7.1 8.3 7.4 8.3 0.08 ≥0.5 ≥175 ≥175 IIIa IIIa Symbol Min ...

  • Page 7

    ... 11.0 12.3 13.5 V 9.5 10.7 12.0 1 unless otherwise noted -3 F(OFF) CC Test Conditions Fig 2 -100 100 Output Open Output Open -3 HCPL-3150 mA, 9, 15, O HCPL-315J V > HCPL-3150 HCPL-315J = HCPL-3150 μA R HCPL-315J μ MHz > 22 Note ...

  • Page 8

    Switching Specifications (AC) Over recommended operating conditions ( Ground, each channel) unless otherwise specified. EE Parameter Symbol Propagation Delay t PLH Time to High Output Level Propagation Delay t PHL Time to Low Output Level Pulse Width PWD ...

  • Page 9

    ... Maximum pulse width = 1 ms, maximum duty cycle = 20 accordance with UL1577, each HCPL-3150 optocoupler is proof tested by applying an insulation test voltage ≥4500 Vrms (≥ 6000 Vrms for the HCPL-315J) for 1 second. This test is performed before the 100% production test for partial discharge (method b) shown in the IEC/EN/ DIN EN 60747-5-2 Insulation Characteristics Table, if applicable ...

  • Page 10

    -100 mA OUT -40 - 100 T – TEMPERATURE ...

  • Page 11

    PLH ° PHL Ω 400 DUTY CYCLE = 50 kHz 300 200 100 ...

  • Page 12

    Figure 17. I Test Circuit Figure 19. V Test Circuit ...

  • Page 13

    ... V CM Figure 24. CMR Test Circuit and Waveforms. Applications Information Eliminating Negative IGBT Gate Drive To keep the IGBT firmly off, the HCPL-3150/315J has a very low maximum V specification of 1 The HCPL- OL 3150/315J realizes this very low V transistor with 4 Ω (typical) on resistance in its pull down circuit. When the HCPL-3150/315J is in the low state, the IGBT gate is shorted to the emitter Ω ...

  • Page 14

    ... HCPL-315J FLOATING SUPPLY 0.1 μF + – 0.1 μF + – Step 2: Check the HCPL-3150/315J Power Dissipation and Increase Rg if Necessary. The HCPL-3150/315J total power dissipa tion Peak Specifica tion. The ( equal to the sum of the emitter power (P T output power ( Duty Cycle O(BIAS) ...

  • Page 15

    ... HCPL-3150 + 270 Ω 2 CONTROL 3 INPUT 74XXX 4 OPEN COLLECTOR Figure 26a. HCPL-3150 Typical Application Circuit with Negative IGBT Gate Drive. HCPL-315J + 270 Ω CONTROL INPUT 2 74XX OPEN COLLECTOR 3 GND 270 Ω CONTROL 7 INPUT 74XX OPEN 8 COLLECTOR GND 1 Figure 26b. HCPL-315J Typical Application Circuit with Negative IGBT Gate Drive. ...

  • Page 16

    ... For Qg = 500 nC, from Figure 27, a value of E gives Ω. Thermal Model (HCPL-3150) The steady state thermal model for the HCPL-3150 is shown in Figure 28a. The thermal resistance values given in this model can be used to calculate the tempera tures at each node for a given operating condition. As shown ...

  • Page 17

    ... T through Thermal Coefficient Data (units in °C/W) Part Number HCPL-315J 198 Note: Maximum junction temperature for above part: 125°C. 17 DETECTOR 1 θ 7 Figure 28b. Thermal Impedance Model for HCPL-315J θ 1 LED 1 LED 2 θ θ ...

  • Page 18

    ... HCPL-3150/315J V the optocoupler output will go into the low state with a typical delay, UVLO Turn Off Delay, of 0.6 μs. When the HCPL-3150/315J output is in the low state and the supply voltage rises above the HCPL-3150/315J achieve (11.0 < V < ...

  • Page 19

    ... Figure 35. The maxi- mum dead time for the HCPL-3150/315J is 700 ns (= 350 ns - (-350 ns)) over an operating temperature range of -40°C to 100°C. Note that the propagation delays used to calculate PDD ...

  • Page 20

    V C LEDP LEDN I LEDN 4 SHIELD Figure 32. Not Recommended Open Collector Drive Circuit. I LED1 V OUT1 OFF V OUT2 I LED2 t PHL MAX t PLH MIN ...

  • Page 21

    ... Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. Obsoletes 5989-2944EN AV02-0164EN - March 28, 2011 800 700 600 500 400 300 200 100 Figure 37a. HCPL-3150: Thermal Derating Curve, Dependence of Safety Limiting Value with Case Tem- perature per IEC/EN/DIN EN 60747-5-2. 200 www.avagotech.com P (mW (mA ...