HCPL-3150 Avago Technologies US Inc., HCPL-3150 Datasheet - Page 17

• Manufacturer Part Number: HCPL-3150
• Description: OPTOCOUPLER GATE DRIVE 0.6A 8DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-3150

• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 600mA
• Propagation Delay High - Low @ If: 300ns @ 7mA ~ 16mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• No. Of Channels: 1
• Isolation Voltage: 3.75kV
• Optocoupler Output Type: Gate Drive
• Input Current: 16mA
• Output Voltage: 30V
• Opto Case Style: DIP
• No. Of Pins: 8
• Propagation Delay Low-high: 0.5µs
• Common Mode Voltage Vcm: 1500V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 516-1125-5

Thermal Coefficient Data
Note: Maximum junction temperature for above part: 125°C.
Thermal Model Dual-Channel (SOIC-16) HCPL-315J Op-
toisolator
Definitions
T
tween nodes as shown in Figure 28b. Ambient Tempera-
ture: Measured approximately 1.25 cm above the opto-
coupler with no forced air.
Description
This thermal model assumes that a 16-pin dual-channel
(SOIC-16) optocoupler is soldered into an 8.5 cm x 8.1
cm printed circuit board (PCB). These optocouplers are
hybrid devices with four die: two LEDs and two detec-
tors. The temperature at the LED and the detector of the
optocoupler can be calculated by using the equations
below.
'T
'T
'T
'T
where:
17
1
, T
E1A
E2A
D1A
D2A
2
Part Number
HCPL-315J
, T
= A
= A
= A
= A
'T
'T
'T
'T
P
P
P
P
A
ances T
E1
E2
D1
D2
xy
3
, T
E1A
E2A
D1A
D2A
11
21
= Power dissipation from LED 1;
= Power dissipation from LED 2;
31
41
thermal coefficient (units in °C/W) is a function of thermal imped-
= Power dissipation from detector 1;
= Power dissipation from detector 2
P
P
4
P
P
, T
= Temperature difference between ambient and LED 1
= Temperature difference between ambient and LED 2
= Temperature difference between ambient and detector 1
= Temperature difference between ambient and detector 2
E1
E1
E1
E1
1
5
+ A
+ A
+ A
+ A
, T
through T
6
12
22
, T
32
42
P
P
P
P
7
E2
E2
E2
E2
, T
+A
+A
+A
+A
A
198
11
8
, T
, A
13
23
33
43
10
(units in °C/W)
22
P
P
9
P
P
.
, T
D1
D1
D1
D1
+A
+A
10
+A
+A
: Thermal impedances be-
14
24
34
44
P
P
A
P
P
12
D2
D2
D2
D2
64
, A
21
A
13
62
, A
31
A
24
64
, A
Figure 28b. Thermal Impedance Model for HCPL-315J.
θ
7
42
DETECTOR 1
A
14
83
, A
θ
θ
LED 1
4
8
41
P
P
E1
E2
θ
A
2
23
90
, A
AMBIENT
32
θ
θ
10
1
θ
3
A
137
33
, A
44
LED 2
θ
DETECTOR 2
θ
5
9
A
34
69
, A
P
P
43
D1
D2
θ
6