HCPL-3150 Avago Technologies US Inc., HCPL-3150 Datasheet - Page 9

• Manufacturer Part Number: HCPL-3150
• Description: OPTOCOUPLER GATE DRIVE 0.6A 8DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-3150

• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 600mA
• Propagation Delay High - Low @ If: 300ns @ 7mA ~ 16mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• No. Of Channels: 1
• Isolation Voltage: 3.75kV
• Optocoupler Output Type: Gate Drive
• Input Current: 16mA
• Output Voltage: 30V
• Opto Case Style: DIP
• No. Of Pins: 8
• Propagation Delay Low-high: 0.5µs
• Common Mode Voltage Vcm: 1500V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 516-1125-5

Package Characteristics (each channel, unless otherwise specified)
*All typical values at T
**The Input-Output/Output-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-out-
put/output-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Avago Ap-
plication Note 1074 entitled “Optocoupler Input-Output Endurance Voltage. ”
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 μs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 70°C free-air temperature at a rate of 4.8 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 5.4 mW/°C. The maximum LED junction tempera ture should not exceed 125°C.
5. Maximum pulse width = 50 μs, maximum duty cycle = 0.5%.
6. In this test V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL1577, each HCPL-3150 optocoupler is proof tested by applying an insulation test voltage ≥4500 Vrms (≥ 6000 Vrms for
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. The difference between t
11. Pins 1 and 4 (HCPL-3150) and pins 3 and 4 (HCPL-315J) need to be connected to LED common.
12. Common mode transient immunity in the high state is the maximum tolerable |dV
13. Common mode transient immunity in a low state is the maximum tolerable |dV
14. This load condition approximates the gate load of a 1200 V/25 A IGBT.
15. Pulse Width Distortion (PWD) is defined as |t
16. Each channel.
17. Device considered a two terminal device: Channel one output side pins shorted together, and channel two output side pins shorted togeth-
18. See the thermal model for the HCPL-315J in the application section of this data sheet.
9
Parameter
Input-Output
Momentary
Withstand Voltage**
Output-Output
Momentary
Withstand Voltage**
Resistance
(Input - Output)
Capacitance C
(Input - Output)
LED-to-Case T
Thermal Resistance
LED-to-Detector
Thermal Resistance
Detector-to-Case
Thermal Resistance
peak minimum = 0.5 A. See Applications section for additional details on limiting I
the HCPL-315J) for 1 second. This test is performed before the 100% production test for partial discharge (method b) shown in the IEC/EN/
DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
output will remain in the high state (i.e., V
put will remain in a low state (i.e., V
er.
OH
LC
I-O
is measured with a dc load current. When driving capacitive loads V
A
= 25°C and V
PHL
and t
Symbol
CC
V
V
R
T
T
O-O
PLH
ISO
I-O
DC
- V
LD
O
EE
between any two parts or channels under the same test condition.
< 1.0 V).
= 30 V, unless otherwise noted.
O
> 15.0 V).
HCPL-3150
HCPL-3150
HCPL-3150
HCPL-3150
HCPL-3150
PHL
HCPL-315J
HCPL-315J
HCPL-315J
-t
Device
PLH
| for any given device.
3750
5000
1500
Min.
Typ.*
10
391
439
119
0.6
1.3
12
CM
OH
/dt| of the common mode pulse, V
OH
CM
will approach V
Max.
/dt| of the common mode pulse, V
peak.
Vrms
Vrms
°C/W
°C/W
°C/W
Units
pF
Ω
CC
as I
OH
Test Conditions
RH < 50%,
t = 1 min.,
T
RH < 50%
t = 1 min.,
T
V
f = 1 MHz
Thermocouple
located at center
underside of
package
A
A
I-O
approaches zero amps.
= 25°C
= 25°C
= 500 V
CM
DC
, to assure that the out-
CM
, to assure that the
Fig.
28
Note
8, 9
17
18
O
9