OPTOCOUPLER 2.0A 250KHZ 8-DIP

HCPL-3180-000E

Manufacturer Part NumberHCPL-3180-000E
DescriptionOPTOCOUPLER 2.0A 250KHZ 8-DIP
ManufacturerAvago Technologies US Inc.
HCPL-3180-000E datasheet
 


Specifications of HCPL-3180-000E

Package / Case8-DIP (0.300", 7.62mm)Voltage - Isolation3750Vrms
Number Of Channels1, UnidirectionalCurrent - Output / Channel2.5A
Propagation Delay High - Low @ If150ns @ 10mACurrent - Dc Forward (if)16mA
Input TypeDCOutput TypeGate Driver
Mounting TypeThrough HoleIsolation Voltage3750 Vrms
Maximum Fall Time0.025 usMaximum Forward Diode Current25 mA
Minimum Forward Diode Voltage1.2 VOutput DeviceIntegrated Photo IC
Configuration1 ChannelMaximum Forward Diode Voltage1.8 V
Maximum Reverse Diode Voltage5 VMaximum Power Dissipation295 mW
Maximum Operating Temperature+ 100 CMinimum Operating Temperature- 40 C
Number Of Elements1Forward Voltage1.8V
Forward Current25mAPackage TypePDIP
Operating Temp Range-40C to 100CPower Dissipation295mW
Propagation Delay Time200nsPin Count8
MountingThrough HoleReverse Breakdown Voltage5V
Operating Temperature ClassificationIndustrialNo. Of Channels1
Optocoupler Output TypeGate DriveInput Current16mA
Output Voltage20VOpto Case StyleDIP
No. Of Pins8Common Mode Ratio10 KV/uS
Rohs CompliantYesLead Free Status / RoHS StatusLead free / RoHS Compliant
Other names516-1674-5  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
Page 4/16

Download datasheet (253Kb)Embed
PrevNext
Recommended Pb-Free IR Profile
t
p
260 +0/-5 °C
T
p
217 °C
T
L
RAMP-UP
3 °C/SEC. MAX.
150 - 200 °C
T
smax
T
smin
t
s
t
L
PREHEAT
60 to 180 SEC.
25
t 25 °C to PEAK
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
= 200 °C, T
= 150 °C
T
smax
smin
Note: Non-halide flux should be used.
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (HCPL-3180 Option 060)
Description
Installation classification per DIN EN 0110 1997-04
for rated mains voltage ≤ 150 V
rms
for rated mains voltage ≤ 300 V
rms
for rated mains voltage ≤ 600 V
rms
Climatic Classification
Pollution Degree (DIN EN 0110 1997-04)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
x 1.875=V
, 100% Production Test with
IORM
PR
t
=1 sec, Partial Discharge < 5 pC
m
Input to Output Test Voltage, Method a*
V
x 1.5=V
, Type and Sample Test, t
IORM
PR
Partial Discharge < 5 pC
Highest Allowable Overvoltage
(Transient Overvoltage t
= 10 sec)
ini
Safety-limiting values – maximum values allowed in the
event of a failure.
Case Temperature
Input Current**
Output Power**
Insulation Resistance at T
, V
= 500 V
S
IO
* Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section IEC/
EN/DIN EN 60747-5-2 for a detailed description of Method a and Method b partial discharge test profiles.
** Refer to the following figure for dependence of P
4
Regulatory Information
The HCPL-3180 has been approved by the following
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
organizations:
20-40 SEC.
IEC/EN/DIN EN 60747-5-2
Approved under: IEC 60747-5-2:1997 + A1:2002
RAMP-DOWN
EN 60747-5-2:2001 + A1:2002
6 °C/SEC. MAX.
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01
(Option 060 only)
60 to 150 SEC.
UL
Approval under UL 1577, component recognition
program up to V
CSA
Approval under CSA Component Acceptance Notice #5,
File CA 88324.
Symbol
V
IORM
V
PR
=60 sec,
V
m
PR
V
IOTM
T
S
I
S,INPUT
P
S, OUTPUT
R
S
and I
on ambient temperature.
S
S
= 3750 V
. File E55361.
rms
ISO
HCPL-3180
Unit
I - IV
I - III
I-II
55/100/21
2
630
V
peak
1181
V
peak
945
V
peak
6000
V
peak
175
°C
230
mA
600
mW
9
>10