ISOLAT 3.75KVRMS 1CH UNIDIR 8DIP

HCPL-2400-000E

Manufacturer Part NumberHCPL-2400-000E
DescriptionISOLAT 3.75KVRMS 1CH UNIDIR 8DIP
ManufacturerAvago Technologies US Inc.
HCPL-2400-000E datasheet
 


Specifications of HCPL-2400-000E

Package / Case8-DIP (0.300", 7.62mm)Voltage - Isolation3750Vrms
Number Of Channels1, UnidirectionalCurrent - Output / Channel25mA
Data Rate40MBdPropagation Delay High - Low @ If33ns @ 7mA
Current - Dc Forward (if)10mAInput TypeDC
Output TypeTri-StateMounting TypeThrough Hole
Isolation Voltage3750 VrmsMaximum Continuous Output Current25 mA
Maximum Fall Time0.01 usMaximum Forward Diode Current10 mA
Minimum Forward Diode Voltage1.1 VOutput DeviceLogic Gate Photo IC
Configuration1 ChannelMaximum Baud Rate40 MBd(Typ)
Maximum Forward Diode Voltage1.5 VMaximum Reverse Diode Voltage2 V
Maximum Power Dissipation350 mWMaximum Operating Temperature+ 70 C
Minimum Operating Temperature0 CNo. Of Channels1
Optocoupler Output TypeLogic GateInput Current8mA
Output Voltage18VOpto Case StyleDIP
No. Of Pins8Body Material1
Common Mode Ratio1000Rohs CompliantYes
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names516-1655-5
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
Page 1/15

Download datasheet (360Kb)Embed
Next
HCPL-2400, HCPL-2430
20 MBd High CMR Logic Gate Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-2400 and HCPL-2430 high speed opto-cou-
plers combine an 820 nm AlGaAs light emitting diode
with a high speed photodetector. This combina-tion re-
sults in very high data rate capability and low input cur-
rent. The totem pole output (HCPL-2430) or three state
output (HCPL-2400) eliminates the need for a pull up re-
sistor and allows for direct drive of data buses.
The detector has optical receiver input stage with built-
in Schmitt trigger to provide logic compatible wave-
forms, eliminating the need for additional waveshaping.
The hysteresis provides differential mode noise immuni-
ty and minimizes the potential for output signal chatter.
The electrical and switching characteristics of the HCPL-
2400 and HCPL-2430 are guaranteed over the tempera-
ture range of 0°C to 70°C.
Functional Diagram
HCPL-2400/11
V
CC
1
NC
8
ANODE 1
2
7
CATHODE 1
6
3
CATHODE 2
4
NC
5
ANODE 2
GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
ENABLE
OUTPUT
ON
L
L
OFF
L
H
ON
H
Z
OFF
H
Z
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
HCPL-2400 Functional Diagram
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Features
• High speed: 40 MBd typical data rate
• High common mode rejection:
HCPL-2400: 10 kV/µs at V
• AC performance guaranteed over temperature
• High speed AlGaAs emitter
• Compatible with TTL, STTL, LSTTL, and HCMOS logic
families
• Totem pole and tri state output (no pull up resistor
required)
• Safety approval
– UL recognized – 3750 V rms for 1 minute per
UL1577
– IEC/EN/DIN EN 60747-5-2 approved with
V
IORM
– CSA approved
• High power supply noise immunity
HCPL-2430
• MIL-PRF-38534 hermetic version available
1
8
V
CC
(HCPL-5400/1 and HCPL-5430/1)
V
2
7
O1
Applications
6
V
3
O2
• Isolation of high speed logic systems
4
5
GND
• Computer-peripheral interfaces
• Switching power supplies
• Isolated bus driver (networking applications)
TRUTH TABLE
(POSITIVE LOGIC)
• Ground loop elimination
LED
OUTPUT
ON
L
• High speed disk drive I/O
OFF
H
• Digital isolation for A/D, D/A conversion
• Pulse transformer replacement
= 300 V (typical)
CM
= 630 V
(Option 060) for HCPL-2400
peak

HCPL-2400-000E Summary of contents

  • Page 1

    ... The totem pole output (HCPL-2430) or three state output (HCPL-2400) eliminates the need for a pull up re- sistor and allows for direct drive of data buses. The detector has optical receiver input stage with built- in Schmitt trigger to provide logic compatible wave- forms, eliminating the need for additional waveshaping ...

  • Page 2

    ... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2430-500E to order product of Gull Wing Surface Mount package in Tape in RoHS compliant. Example 2: HCPl-2400 to order product of 8-Pin DIP package in tube packaging and non RoHS compliant. ...

  • Page 3

    ... Schematic ANODE + V F – CATHODE 3 TRUTH TABLE (POSITIVE LOGIC) LED ENABLE OUTPUT OFF OFF – GND – SHIELD TRUTH TABLE (POSITIVE LOGIC) LED OUTPUT ON OFF HCPL-2400 Schematic GND L H ...

  • Page 4

    ... Package Outline Drawings 8-Pin DIP Package (HCPL-2400, HCPL-2430) 9.65 ± 0.25 (0.380 ± 0.010 TYPE NUMBER A XXXXZ YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2400, HCPL-2430) 9.65 ± ...

  • Page 5

    ... THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX 200 ° 150 °C smax smin Note: Non-halide flux should be used. Regulatory Information The HCPL-24XX has been approved by the following organizations: VDE Approved according to VDE 0884/06.92 (Option 060 only). UL Recognized under UL 1577, Component Recognition Program, File E55361. 5 ...

  • Page 6

    ... Tracking Index) Isolation Group Option 300 - surface mount classification is Class A in accordance with CECC 00802. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-2400 OPTION 060 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms for rated mains voltage ≤450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1 ...

  • Page 7

    ... Lead Solder Temperature (for Through Hole Devices) Reflow Temperature Profile (Option #300) Recommended Operating Conditions Parameter Power Supply Voltage Forward Input Current (ON) Forward Input Voltage (OFF) Fan Out Enable Voltage (Low) HCPL-2400 Only) Enable Voltage (High) HCPL-2400 Only) Operating Temperature 7 Symbol Minimum F(AVG) ...

  • Page 8

    ... F Coefficient of ∆T A Forward Voltage Input Capacitance C IN *All typical values 25°C and unless otherwise noted ≤8 mA ≤V ≤0.8 V. All typicals at T F(ON) F(OFF) Device HCPL- Min. Typ.* Max. Units 0.5 V 2.4 V 2.7 100 µA 2400 2.0 V 2400 0.8 V 2400 20 µA ...

  • Page 9

    ... Logic High Common | Mode Transient Immunity Logic Low Common | Mode Transient Immunity Power Supply Noise PSNI Immunity *All typical values 25°C and unless otherwise noted ≤ ≤ V ≤ 0.8 V. All typicals at T F(ON) F(OFF) Device HCPL- Min. Typ.* Max. Units ...

  • Page 10

    ... The typical data shown is indicative of what can be expected using the application circuit in Figure 13. 6. This specification simulates the worst case operating conditions of the HCPL-2400 over the recommended operating temperature and V with the suggested application circuit of Figure 13. ...

  • Page 11

    Figure 1. Typical logic low output voltage vs. logic low output current. Figure 4. Typical diode input forward current charac- teristic. Figure 6. Typical propagation delay vs. ambient temperature. 11 Figure 2. Typical logic high output voltage vs. logic high ...

  • Page 12

    ... Figure 10. Typical enable propagation delay vs. ambi- ent temperature. 800 P (mW) S 700 I (mA) S 600 500 400 300 200 100 100 125 150 175 200 T – CASE TEMPERATURE – °C S Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2. HCPL-2400 fig 12 ...

  • Page 13

    ... Applications Figure 13. Recommended 20 MBd HCPL-2400/30 interface circuit 50 PSK Figure 15. Illustration of propagation delay skew – t PSK HCPL-2400 fig 15 Figure 17. Modulation code selections. 13 Figure 14. Alternative HCPL-2400/30 interface circuit. INPUTS OUTPUTS . Figure 16. Parallel data transmission example. Figure 18. Typical HCPL-2400/30 output schematic. DATA ...

  • Page 14

    ... PLH PHL a problem. The HCPL-2400/30 optocouplers offer the advantages of guaranteed specifications for propagation delays, pulse- width distortion, and propagation delay skew over the recommended temperature, input current, and power supply ranges. ...

  • Page 15

    ... Switching performance of the HCPL-2400/30 optocou- plers is not sensitive to the TTL logic family used in the recommended drive circuit. The typical and worst-case switching parameters given in the data sheet can be met using common 74LS TTL inverting gates or buffers. Use of faster TTL families will slightly reduce the overall ...