HCPL-2400-000E Avago Technologies US Inc., HCPL-2400-000E Datasheet - Page 10

• Manufacturer Part Number: HCPL-2400-000E
• Description: ISOLAT 3.75KVRMS 1CH UNIDIR 8DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-2400-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 25mA
• Data Rate: 40MBd
• Propagation Delay High - Low @ If: 33ns @ 7mA
• Current - Dc Forward (if): 10mA
• Input Type: DC
• Output Type: Tri-State
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 25 mA
• Maximum Fall Time: 0.01 us
• Maximum Forward Diode Current: 10 mA
• Minimum Forward Diode Voltage: 1.1 V
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 40 MBd(Typ)
• Maximum Forward Diode Voltage: 1.5 V
• Maximum Reverse Diode Voltage: 2 V
• Maximum Power Dissipation: 350 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• No. Of Channels: 1
• Optocoupler Output Type: Logic Gate
• Input Current: 8mA
• Output Voltage: 18V
• Opto Case Style: DIP
• No. Of Pins: 8
• Body Material: 1
• Common Mode Ratio: 1000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1655-5

10
Package Characteristics
*All typical values are at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Related Characteristics Table (if applicable), your equipment lev-
el safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage, ” publication number 5963-2203E.
Notes:
10. Power Supply Noise Immunity is the peak to peak amplitude of the ac ripple voltage on the V
11. Use of a 0.1 µF bypass capacitor connected between pins 8 and 5 adjacent to the device is required.
12. Peak Forward Input Current pulse width < 50 µs at 1 KHz maximum repetition rate.
13. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for one second (leakage detec-
1. Each channel.
2. Duration of output short circuit time not to exceed 10 ms.
3. Device considered a two terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
4. t
5. The typical data shown is indicative of what can be expected using the application circuit in Figure 13.
6. This specification simulates the worst case operating conditions of the HCPL-2400 over the recommended operating temperature and V
7. Propagation delay skew is discussed later in this data sheet.
8. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
9. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
Parameter
Input-Output
Momentary
Withstand Voltage**
Input-Output
Resistance
Input-Output
Capacitance
Input-Input
Insulation Leakage
Current
Resistance
(Input-Input)
Capacitance
(Input-Input)
output pulse. The t
rising edge of the output pulse.
with the suggested application circuit of Figure 13.
that the output will remain in a Logic High state (i.e., V
able (negative) dV
in the desired logic state. For desired logic high state, V
tion current limit, I
Characteristics Table, if applicable.
PHL
propagation delay is measured from the 50% level on the rising edge of the input current pulse to the 1.5 V level on the falling edge of the
CM
I-O
PLH
/dt of the common mode pulse, V
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related
A
propagation delay is measured from the 50% level on the falling edge of the input current pulse to the 1.5 V level on the
= 25°C.
Sym.
V
R
C
C
R
I
ISO
I-I
I-O
I-O
I-I
I-I
Device
2430
2430
2430
CM
3750
O
Min.
OH(MIN)
, to assure that the output will remain in a Logic Low state (i.e., V
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum toler-
> 2.0 V, and for desired logic low state, V
0.005
Typ.*
0.25
10
10
0.6
12
11
Max.
Units
V rms
µA
pF
pF
Ω
Ω
CC
line that the device will withstand and still remain
Test Conditions
CM
/dt of the common mode pulse, V
RH ≤50%,
t = 1 min.,
T
V
f = 1 MHz
V
RH ≤45%
t = 5 s,
V
V
f = 1 MHz
A
I-O
I-O
I-I
I-I
= 25°C
OL(MAX)
= 500 Vdc
= 500 Vdc
= 500 Vdc
= 0 Vdc
< 0.8 V.
O
< 0.8 V).
Fig.
CM
, to assure
3, 13
Note
CC
3
8
8
8
range