PS9117A-V-F3-AX CEL, PS9117A-V-F3-AX Datasheet
PS9117A-V-F3-AX
Specifications of PS9117A-V-F3-AX
Available stocks
Related parts for PS9117A-V-F3-AX
PS9117A-V-F3-AX Summary of contents
Page 1
... HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE DESCRIPTION The PS9117A is an optically coupled high-speed, active low type isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9117A is designed specifically for high common mode transient immunity (CMR) and low pulse width distortion ...
Page 2
... Type Number Assembly Lot No. 1 pin Mark *1 Initial of NEC (Engraved mark) Week Assembled Year Assembled (Last 1 Digit) Rank Code *1 Bar : Pb-Free Data Sheet PN10646EJ04V0DS PS9117A 7.0±0.3 4.4 0.5±0.3 PLATING 117A Type Number N831 Assembly Lot * Week Assembled Year Assembled ...
Page 3
... PS9117A-F3 PS9117A-F3-A PS9117A-V PS9117A-V-A PS9117A-V-F3 PS9117A-V-F3-A PS9117A PS9117A-AX PS9117A-F3 PS9117A-F3-AX PS9117A-V PS9117A-V-AX PS9117A-V-F3 PS9117A-V-F3-AX *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (T Parameter *1 Diode Forward Current Reverse Voltage Supply Voltage Detector Output Voltage Output Current *2 ...
Page 4
... 7 THHL THLH ⏐t ⏐ t PHL- PLH t PSK = 350 Ω 25° > mA 350 Ω 25° < 0 7.5 mA Data Sheet PN10646EJ04V0DS PS9117A *1 MIN. TYP. MAX. Unit 1.4 1.65 1.8 V μ μ 1 100 A 0.2 0 Ω 0 100 45 75 100 μ kV/ s μ kV/ ...
Page 5
... Avoid storage at a high temperature and high humidity. Input μ = 350 Ω 0 (monitor Output 90 10% = 350 Ω μ 0 (monitor mA 7.5 mA) F and GND near device. Also, ensure that the distance between CC Data Sheet PN10646EJ04V0DS PS9117A = 2 7.5 mA) F 50% 1 PHL PLH 0 ...
Page 6
... I CCL +50˚C +25˚ 0˚C CCH –25˚ 2.2 2.4 –50 –25 LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 0 0.5 0.4 0.3 0.2 0 –50 –25 Data Sheet PN10646EJ04V0DS PS9117A 100 Ambient Temperature T (˚ 100 Ambient Temperature T (˚ 5 ...
Page 7
... Ambient Temperature T PROPAGATION DELAY TIME vs. FORWARD 100 PLH 350 Ω 100 5 7 Data Sheet PN10646EJ04V0DS PS9117A 4.7 kΩ PLH 4.0 kΩ PLH 1.0 kΩ PLH L = 350 Ω PLH L = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ ...
Page 8
... Outline and Dimensions (Reel) R 1.0 Packing: 2 500 pcs/reel 8 3.45 MAX. +0.1 1.5 –0 3.9±0.1 3.0±0.1 8.0±0.1 0.3 ±0.05 PS9117A-F3 2.0±0.5 13.0±0.2 21.0±0.8 Data Sheet PN10646EJ04V0DS PS9117A 2.0±0.5 13.5±1.0 17.5±1.0 11.9 to 15.4 Outer edge of flange ...
Page 9
... RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) 1.45 5.5 Data Sheet PN10646EJ04V0DS PS9117A 9 ...
Page 10
... Wt% is recommended.) (heating 180˚C 120±30 s (preheating) Time (s) 350°C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Data Sheet PN10646EJ04V0DS PS9117A 260˚C MAX. 220˚C ...
Page 11
... Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Data Sheet PN10646EJ04V0DS PS9117A 11 ...
Page 12
... Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current I , Psi = 0) F Power (output or total power dissipation) Isolation resistance V = 500 Tsi Parameter Data Sheet PN10646EJ04V0DS PS9117A Symbol Speck Unit IV III 40/85/21 U 707 V IORM peak U 1 061 V pr ...
Page 13
... NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). Data Sheet PN10646EJ04V0DS PS9117A Not all M8E 02. 11-1 13 ...
Page 14
... Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. PS9117A ...