HCPL-260L#560 Avago Technologies US Inc., HCPL-260L#560 Datasheet

OPTOCOUPLER 15MBD 3.3V VDE 8-SMD

HCPL-260L#560

Manufacturer Part Number
HCPL-260L#560
Description
OPTOCOUPLER 15MBD 3.3V VDE 8-SMD
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of HCPL-260L#560

Package / Case
8-SMD Gull Wing
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
50mA
Data Rate
15MBd
Propagation Delay High - Low @ If
50ns @ 7.5mA
Current - Dc Forward (if)
20mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount, Gull Wing
Isolation Voltage
3750 Vrms
Maximum Continuous Output Current
50 mA
Maximum Fall Time
20 ns
Maximum Forward Diode Current
20 mA
Maximum Rise Time
45 ns
Minimum Forward Diode Voltage
1.4 V
Output Device
Logic Gate Photo IC
Configuration
1 Channel
Maximum Baud Rate
15 MBps
Maximum Forward Diode Voltage
1.75 V
Maximum Reverse Diode Voltage
5 V
Maximum Power Dissipation
85 mW
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-260L#560HCPL-260L
Manufacturer:
AGILENT
Quantity:
74
Company:
Part Number:
HCPL-260L#560HCPL-260L
Manufacturer:
AVAGO
Quantity:
8 000
Company:
Part Number:
HCPL-260L#560HCPL-260L
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Company:
Part Number:
HCPL-260L#560HCPL-260L
Quantity:
27
Company:
Part Number:
HCPL-260L#560HCPL-260L-000E
Manufacturer:
AVAGO
Quantity:
30 000
CATHODE
HCPL-260L/060L/263L/063L
High Speed LVTTL Compatible 3.3 Volt Optocouplers
Data Sheet
Description
The HCPL-260L/060L/263L/063L are optically coupled
gates that combine a GaAsP light emitting diode and
an integrated high gain photo detector. An enable in-
put allows the detector to be strobed. The output of
the detector IC is an open collector Schottky-clamped
transistor. The internal shield provides a guaranteed
common mode transient immunity specification of
15 kV/μs at 3.3V.
This unique design provides maximum AC and DC circuit
isolation while achieving LVTTL/LVCMOS compati-bili-
ty. The optocoupler AC and DC operational parameters
are guaranteed from –40qC to +85qC allowing trouble-
free system performance.
These optocouplers are suitable for high speed logic
interfacing, input/output buffering, as line receivers in
environments that conventional line receivers cannot
tolerate and are recommended for use in extremely high
ground or induced noise environments.
Functional Diagram
ANODE
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
NC
NC
LED
ON
OFF
ON
OFF
ON
OFF
1
2
3
4
(POSITIVE LOGIC)
HCPL-260L/060L
TRUTH TABLE
ENABLE
Lead (Pb) Free
RoHS 6 fully
compliant
SHIELD
NC
NC
H
H
L
L
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
OUTPUT
H
H
H
H
L
L
8
7
6
5
V
V
V
GND
CC
E
O
A 0.1 μF bypass capacitor must be
connected between pins 5 and 8.
CATHODE
CATHODE
ANODE
ANODE
2
1
1
2
1
2
3
4
(POSITIVE LOGIC)
HCPL-263L/063L
LED
ON
OFF
TRUTH TABLE
SHIELD
OUTPUT
H
L
8
7
6
5
V
V
V
GND
CC
O1
O2
Features
x 3.3V/5V Dual Supply Voltages
x Low power consumption
x 15 kV/μs minimum Common Mode Rejection (CMR) at
x High speed: 15 MBd typical
x LVTTL/LVCMOS compatible
x Low input current capability: 5 mA
x Guaranteed AC and DC performance over tempera-
x Available in 8-pin DIP, SOIC-8
x Strobable output (single channel products only)
x Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-2
Applications
x Isolated line receiver
x Computer-peripheral interfaces
x Microprocessor system interfaces
x Digital isolation for A/D, D/A conversion
x Switching power supply
x Instrument input/output isolation
x Ground loop elimination
x Pulse transformer replacement
x Field buses
V
ture: –40qC to +85qC
CM
= 1000 V

Related parts for HCPL-260L#560

HCPL-260L#560 Summary of contents

Page 1

... RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description The HCPL-260L/060L/263L/063L are optically coupled gates that combine a GaAsP light emitting diode and an integrated high gain photo detector. An enable in- put allows the detector to be strobed. The output of the detector open collector Schottky-clamped transistor. The internal shield provides a guaranteed common mode transient immunity specifi ...

Page 2

... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Combination of Option 020 and Option 060 is not available. Example 1: HCPL-260L-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-263L to order product of 300mil DIP package in tube packaging and non RoHS compliant ...

Page 3

... MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). 0.65 (0.025) MAX. * MARKING CODE LETTER FOR OPTION NUMBERS 2.54 ± 0.25 "V" = OPTION 060 (0.100 ± 0.010) OPTION NUMBER 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. HCPL-263L/063L ...

Page 4

... DIP Package with Gull Wing Surface Mount in Option 500 (HCPL-260L, HCPL-263L) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. ...

Page 5

Solder Reflow Temperature Profile 300 PREHEATING RATE 3 REFLOW HEATING RATE 2.5 200 160 C 150 C 140 C 100 ROOM TEMPERATURE Note: Non-halide flux should be used. Recommended PB-Free IR Profile 260 +0/- ...

Page 6

... Regulatory Information The HCPL-260L/060L/263L/063L have been approved by the following organizations: UL Approval under UL 1577, Component Recognition Program, File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (Option 060 only) Insulation and Safety Related Specifi ...

Page 7

... T – CASE TEMPERATURE – Symbol V IORM IOTM S,INPUT P S,OUTPUT R S HCPL-260L/HCPL-263L 800 P (mW) S 700 I (mA) S 600 500 400 300 200 100 0 200 100 125 150 175 T – CASE TEMPERATURE – PDIP Option 060 SO-8 Option 060 I-IV ...

Page 8

Absolute Maximum Ratings (No Derating Required up to 85˚C) Parameter Storage Temperature Operating Temperature† Average Forward Input Current Reverse Input Voltage Input Power Dissipation Supply Voltage (1 Minute Maximum) Enable Input Voltage (Not to Exceed V by more than 500 ...

Page 9

Electrical Specifications Over Recommended Operating Conditions (T All Typicals 3 25qC. All enable test conditions apply to single channel products only. See Note Parameter Sym. Device High Level ...

Page 10

Electrical Specifications (DC) Over recommended operating conditions ( qC. All typicals Parameter Symbol Channel High Level Output I OH Current Input Threshold I Single TH Current Dual Low Level Output ...

Page 11

Switching Specifications Over Recommended Operating Conditions (T specified. All Typicals 25qC Parameter Symbol Propagation Delay t PLH Time to High Output Level Propagation Delay t PHL Time to Low Output Level Pulse Width |t PHL ...

Page 12

... HCPL-060L Output Low Level |CM | HCPL-263L L Common Mode HCPL-063L Transient Immunity HCPL-260L HCPL-060L Output High Level |CM | HCPL-263L H Common Mode HCPL-063L Transient Immunity HCPL-260L HCPL-060L Output Low Level |CM | HCPL-263L L Common Mode HCPL-063L Transient Immunity HCPL-260L HCPL-060L 12 Min. Typ. Units Test Conditions 15 25 kV/ ...

Page 13

Package Characteristics All Typicals 25˚C. A Parameter Sym. Package Input-Output I * Single 8-Pin DIP I-O Insulation Single SO-8 Input-Output V 8-Pin DIP, SO-8 ISO Momentary Withstand Voltage** Input-Output R 8-Pin, SO-8 I-O Resistance Input-Output C 8-Pin ...

Page 14

250 μ FOR SINGLE CHANNEL PRODUCTS ONLY 5 0 -60 -40 - 100 T ...

Page 15

FOR SINGLE 2.0 V* CHANNEL 0.6 V PRODUCTS ONLY 5 -60 -40 - 100 60 ...

Page 16

120 350 Ω PLH 350 Ω PHL -60 -40 - 100 ...

Page 17

PULSE GEN Ω INPUT V E MONITORING NODE 7.5 mA 0.1 μ BYPASS GND Figure 9. ...

Page 18

CC1 220 Ω D1 – GND 1 SHIELD 1 *DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT. 3 ...

Page 19

... Application Information Common-Mode Rejection for HCPL-260L Families: Figure 13 shows the recom mended drive circuit for op- timal common-mode rejection performance. Two main points to note are: 1. The enable pin is tied to V rather than floating (this CC applies to single-channel parts only). 2. Two LED-current setting resistors are used instead of one ...

Page 20

... ANY OPEN-COLLECTOR/ OPEN-DRAIN LOGIC GATE) Figure 16. TTL open-collector/open drain gate drive circuit. 74HC04 (OR ANY TOTEM-POLE OUTPUT LOGIC GATE) Figure 17. CMOS gate drive circuit. www.avagotech.com V CC HCPL-260L 1 420 Ω (MAX) 2 2N3906 (ANY PNP) LED 74HC00 HCPL-260L 1 1N4148 2 220 Ω HCPL-260L LED LED ...

Related keywords