HCPL-060L Avago Technologies US Inc., HCPL-060L Datasheet - Page 13

OPTOCOUPLER 15MBD 3.3V 8-SOIC

HCPL-060L

Manufacturer Part Number
HCPL-060L
Description
OPTOCOUPLER 15MBD 3.3V 8-SOIC
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of HCPL-060L

Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
50mA
Data Rate
15MBd
Propagation Delay High - Low @ If
50ns @ 7.5mA
Current - Dc Forward (if)
20mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
No. Of Channels
1
Isolation Voltage
3.75kV
Optocoupler Output Type
Logic Gate
Input Current
15mA
Output Voltage
7V
Opto Case Style
SOIC
No. Of Pins
8
Common Mode Voltage Vcm
1000V
Forward Voltage
1.5V
Number Of Elements
1
Baud Rate
15Mbps
Forward Current
20mA
Output Current
50mA
Package Type
SOIC
Operating Temp Range
-40C to 85C
Power Dissipation
85mW
Propagation Delay Time
90ns
Pin Count
8
Mounting
Surface Mount
Reverse Breakdown Voltage
5V
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant, Contains lead / RoHS non-compliant
Other names
516-1100-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HCPL-060L
Manufacturer:
AVAGO
Quantity:
3 000
Part Number:
HCPL-060L
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-060L#060
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-060L#500
Manufacturer:
AVAGO
Quantity:
3 000
Part Number:
HCPL-060L-000E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-060L-060
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-060L-060E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-060L-500
Manufacturer:
AVAGO
Quantity:
3 232
Part Number:
HCPL-060L-500E
Quantity:
12 000
Part Number:
HCPL-060L-500E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-060L-500E
Manufacturer:
AVAGO
Quantity:
13 349
Part Number:
HCPL-060L-560E
Manufacturer:
AVAGO
Quantity:
18 636
13
Package Characteristics
All Typicals at T
Parameter
Input-Output
Insulation
Input-Output
Momentary
Withstand
Voltage**
Input-Output
Resistance
Input-Output
Capacitance
Input-Input
Insulation
Leakage
Current
Resistance
(Input-Input)
Capacitance
(Input-Input)
*The JEDEC Registration specifies 0˚C to +70˚C. Avago specifies –40˚C to +85˚C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
10. The t
11. The t
12. CM
13. CM
14. For sinusoidal voltages, (|dV
15. No external pull up is required for a high logic state on the enable input. If the V
16. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
17. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for one second (leakage
18. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for one second (leakage
19. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only.
20. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only.
1. Each channel.
2. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
3. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
4. Derate linearly above +80˚C free-air temperature at a rate of 2.7 mW/˚C for the SOIC-8 package.
5. Bypassing of the power supply line is required, with a 0.1 μF ceramic disc capacitor adjacent to each optocoupler as illustrated in
6. The t
7. The t
8. t
9. See test circuit for measurement details.
exceed 20 mA.
exceed 15 mA.
Figure 11. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
of the output pulse.
of the output pulse.
conditions.
rising edge of the output pulse.
falling edge of the output pulse.
(i.e., V
(i.e., V
CMR performance. For single channel products only. See application information provided.
detection current limit, I
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
detection current limit, I
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
PSK
H
L
is equal to the worst case difference in t
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state
PLH
PHL
ELH
ELH
is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state
o
o
> 2.0 V).
< 0.8 V).
propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge
propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge
enable propagation delay is measured from the 1.5 V point on the falling edge of the enable input pulse to the 1.5 V point on the
enable propagation delay is measured from the 1.5 V point on the rising edge of the enable input pulse to the 1.5 V point on the
A
Sym.
I
V
R
C
I
R
C
= 25˚C.
I-O
I-I
ISO
I-O
I-O
I-I
I-I
*
I-O
I-O
Package
Single 8-Pin DIP
Single SO-8
8-Pin DIP, SO-8
8-Pin, SO-8
8-Pin DIP, SO-8
Dual Channel
Dual Channel
Dual 8-Pin Dip
Dual SO-8
≤ 5 μA). This test is performed before the 100% production test for partial discharge (Method b) shown in the
≤ 5 μA). This test is performed before the 100% production test for partial discharge (Method b) shown in the
CM
| / dt)
max
= πf
PHL
CM
V
and/or t
CM
Min.
3750
(p-p).
PLH
that will be seen between units at any given temperature and specified test
Typ.
10
0.6
0.005
10
0.03
0.25
12
11
Max
1
E
Units
μA
V rms
Ω
pF
μA
Ω
pG
pin is not used, tying V
Test Conditions
45% RH, t = 5 s,
V
RH ≤ 50%, t = 1 min,
T
V
f = 1 MHz, T
RH ≤ 45%, t = 5 s,
V
f = 1 MHz
A
I-O
I-O
I-I
= 25˚C
= 500 V
= 3 kV DC, T
=500 V dc
E
A
to V
= 25˚C
A
CC
= 25˚C
will result in improved
Fig.
Note
16, 17
16, 17
1, 16, 19
1, 16, 19
20
20
20

Related parts for HCPL-060L