HCPL-073A Avago Technologies US Inc., HCPL-073A Datasheet
HCPL-073A
Specifications of HCPL-073A
Available stocks
Related parts for HCPL-073A
HCPL-073A Summary of contents
Page 1
... GND *5000 V rms/1 Minute rating is for Option 020 (HCPL-4701 and HCPL-4731) products only. A 0.1 F bypass capacitor connected between pins 8 and 5 is recommended. CAUTION advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. ...
Page 2
... The HCPL-4731 represents the dual channel 8-Pin DIP configuration and is pin compatible with the popular standard HCPL-2731. The HCPL-070A and HCPL-073A are the equivalent single and dual channel products in an SO-8 footprint. Each channel can be driven with an input current as low and has a typical current transfer ratio of 3500% ...
Page 3
... Ordering Information HCPL-4701, HCPL-4731, HCPL-070A and HCPL-073A are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part RoHS non RoHS Number Compliant Compliant Package -000E no option 300 mil DIP-8 -300E ...
Page 4
... Schematic HCPL-4701 and HCPL-070A ANODE + V F – CATHODE SHIELD 4 HCPL-4731 and HCPL-073A – – GND SHIELD USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE GND 5 ...
Page 5
... A XXXXZ YYWW 1 2 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4701, HCPL-4731) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...
Page 6
... Small-Outline SO-8 Package (HCPL-070A, HCPL-073A XXX 3.937 ± 0.127 YWW (0.155 ± 0.005 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES) ...
Page 7
... Volts IIIa IIIa Regulatory Information The HCPL-4701/4731 and HCPL- 070A/073A have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 ...
Page 8
... Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application sec 500 V (HCPL-4701 OPTION 060 ONLY) Symbol Characteristic Units I-IV I-III 55/85/21 2 ...
Page 9
... Peak Transient Input Current (HCPL-070A/073A) (50% Duty Cycle Pulse Width) Reverse Input Voltage Input Power Dissipation (Each Channel) Output Current (Each Channel) Emitter Base Reverse Voltage (HCPL-4701/070A) Output Transistor Base Current (HCPL-4701/070A) Supply Voltage Output Voltage Output Power Dissipation (Each Channel) Total Power Dissipation (Each Channel) ...
Page 10
... Electrical Specifications 4 1 specified. All Typicals See note 8. A Device Parameter Symbol HCPL- Current CTR Transfer Ratio Logic Low V OL Output Voltage Logic High I OH Output Current Logic Low I 4701/070A CCL Supply Current 4731/073A Logic High I 4701/070A CCH Supply Current 4731/073A ...
Page 11
... Immunity at Logic High Output Common Mode | Transient Immunity at Logic Low Output *All typical values and Package Characteristics Parameter Symbol HCPL- Min. Typ.* Max. Units Input-Output Momentary V Withstand Voltage** Option 020 Resistance R (Input-Output) Capacitance C (Input-Output) Insulation Leakage Current (Input-Input) Resistance (Input-Input) R Capacitance ...
Page 12
... Significant reduction in overall gain can occur when using resistor values below 47 k for single channel product. 11. The Applications Information section of this data sheet references the HCPL-47XX part family, but applies equally to the HCPL-070A and HCPL- 073A parts. 1.25 NORMALIZED 0 ...
Page 13
... HCPL-4701, or the dual-channel HCPL-4731 low- power optocouplers. Either or both of these two devices are referred to in this text as HCPL- 47XX product(s). These opto- couplers are Avago’s lowest input current, low-power optocouplers. Low-power isolation can be defined as less than a milliwatt of ...
Page 14
... Table 1. Typical HCPL-4701 Power Dissipation for 3 V and 5 V Applications Power Dissipation ( W) P LED P Vcc [1] P O-C [2] P TOTAL Notes open-collector (o-c) pull-up resistor was used for both 3.3 Vdc and 5 Vdc calculations For typical total interface circuit power consumption in 3.3 Vdc application, add to P ...
Page 15
... P0WER PRIMARY SUPPLY NOTE: THE CIRCUITS SHOWN IN THIS FIGURE REPRESENT POSSIBLE, FUNCTIONAL APPLICATION OF THE HCPL-47XX OPTOCOUPLER TO AN ISDN LINE INTERFACE. THIS CIRCUIT ARRANGEMENT DOES NOT GUARANTEE COMPLIANCE, CONFORMITY, OR ACCEPTANCE TO AN ISDN, OR OTHER TELECOMMUNICATION STANDARD FCC OR TO OTHER GOVERNMENTAL REGULATORY AGENCY REQUIREMENTS. THESE CIRCUITS ARE RECOMMENDATIONS THAT MAY MEET THE NEEDS OF THESE APPLICATIONS ...
Page 16
... Data Communication and Input/Output Interfaces In data communication, the HCPL-47XX can be used as a line receiver on a RS-232-C line or this optocoupler can be part of a proprietary data link with low input current, multi-drop stations along the data path. Also, this low-power optocoupler can be used within equipment that monitors the presence of high- voltage ...
Page 17
... ACTIVE OUTPUT OR OPEN COLLECTOR Figure 15. Series LED Driver Circuit for HCPL-4701/-4731. For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. Obsoletes 5989-2106EN ...