HCPL-4200 Avago Technologies US Inc., HCPL-4200 Datasheet
HCPL-4200
Specifications of HCPL-4200
Available stocks
Related parts for HCPL-4200
HCPL-4200 Summary of contents
Page 1
... Optical coupling of the signal from the 20 mA current loop to the logic output breaks ground loops and provides for a very high common mode rejection. The HCPL-4200 aids in the design process by providing Functional Diagram A 0.1 F bypass capacitor connected between pins 8 and 5 is recommended. HCPL-4200 ...
Page 2
... A XXXX YYWW 1 2 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 8 Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4200) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...
Page 3
... PEAK TIME NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX 200 ° 150 °C smax smin Figure 1b. Pb-Free IR Profile. Regulatory Information The HCPL-4200 has been approved by the following organizations: PEAK PEAK TEMP. TEMP. 245°C 240°C PEAK TEMP. ...
Page 4
Insulation and Safety Related Specifications Parameter Min. External Air Gap (External Clearance) Min. External Tracking Path (External Creepage) Min. Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group Option 300 – surface mount classification is Class A ...
Page 5
DC Electrical Specifications For 4 noted. See note 13. Parameter Symbol Min. Typ. Max. Units Mark State Input I MI Current Mark State Input V MI Voltage Space State Input I ...
Page 6
Switching Specifications For 4 otherwise noted. See note 13. Parameter Symbol Propagation Delay Time to Logic High Output Level Propagation Delay Time to Logic Low Output Level Propagation Delay Time t ...
Page 7
Notes pulse width, 300 pps. 2. Derate linearly above 70 C free air temperature at a rate of 1.6 mW/ C. Proper application of the derating factors will prevent IC junction temperatures from exceeding 125 C for ...
Page 8
Figure 8. Test Circuit for PHL PLH r 0 0.4 0.3 t PLH 0.2 t PHL 0.1 0 -60 -40 - ...
Page 9
... The maximum compliance level is determined by the trans- mitter breakdown characteristic. A recommended non-isolated active transmitter circuit which can be used with the HCPL-4200 in point-to-point or in multidrop 20 mA current loop applications is given in Figure 18. The current source is controlled via a standard TTL 7407 buffer to ...
Page 10
... Typical data rate performance versus distance is illustrated in Figure 20 for the combination of a non-isolated active transmitter and HCPL-4200 optically coupled current loop receiver shown in Figure 18. Curves are shown for 10% and 25% distortion data rate. 10% (25%) distortion data rate is defined as that rate at ...
Page 11
... Figure 18. Recommended Non-Isolated Active Transmitter with HCPL-4200 Isolated Receiver for Simplex Point-to-Point 20 mA Current Loop. receiver, can be used at the isolated end of current loops. Cross talk and common mode coupling are greatly reduced when optical isolation is imple- mented at the same end of both loops, as shown ...
Page 12
... Voltage compliance of the current source must adequate level for operating all units in the loop while not exceeding 27 V dc, the maximum breakdown voltage for the HCPL-4100. Note that the HCPL-4100 transmitter will allow loop current to conduct when input V power is off. Consult CC ...