BFC238320623 Vishay, BFC238320623 Datasheet - Page 21

CAP FILM MMKP .062UF 630VDC 5%

BFC238320623

Manufacturer Part Number
BFC238320623
Description
CAP FILM MMKP .062UF 630VDC 5%
Manufacturer
Vishay
Series
MMKP 383r
Datasheet

Specifications of BFC238320623

Capacitance
0.062µF
Voltage - Ac
220V
Voltage - Dc
630V
Dielectric Material
Polypropylene, Metallized
Tolerance
±5%
Operating Temperature
-55°C ~ 105°C
Mounting Type
Through Hole
Package / Case
Radial
Size / Dimension
0.689" L x 0.276" W (17.50mm x 7.00mm)
Height
0.532" (13.50mm)
Termination
PC Pins
Lead Spacing
0.591" (15.00mm)
Features
AC and Pulse
Voltage Rating
630 Volts
Termination Style
Radial
Product
AC Pulse / Snubber Metallized Polypropylene Capacitors
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Esr (equivalent Series Resistance)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
2222 383 20623
222238320623
BC1877
BFC2 383 20623
BFC2 383 20623
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
The temperature is measured in unloaded (T
The temperature rise is given by ΔT = T
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (U
2. The peak-to-peak voltage (U
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
Document Number: 28124
Revision: 03-Mar-10
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration.
temperature rise).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
2
×
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
T
0
dU
------- -
dt
2
×
dt
<
U
Rdc
AC and Pulse Double Metallized Polypropylene
P
×
) shall not be greater than the rated DC voltage (U
Film Capacitors MMKP Radial Potted Type
dU
------- -
dt
rated
P-P
) shall not be greater than 2
C
- T
For technical questions, contact:
amb
amb
.
) and maximum loaded condition (T
2 x U
Rac
to avoid the ionisation inception level
dc-film@vishay.com
Thermocouple
Rdc
)
C
).
Vishay BCcomponents
MMKP 383
www.vishay.com
Rdc
and
207

Related parts for BFC238320623