MDLS-40263-C-HT-HV-FSTN-LED3G Varitronix, MDLS-40263-C-HT-HV-FSTN-LED3G Datasheet

LCD MOD 40X2 CHAR FSTN GN BKLT

MDLS-40263-C-HT-HV-FSTN-LED3G

Manufacturer Part Number
MDLS-40263-C-HT-HV-FSTN-LED3G
Description
LCD MOD 40X2 CHAR FSTN GN BKLT
Manufacturer
Varitronix
Series
MDL(S)-40263r

Specifications of MDLS-40263-C-HT-HV-FSTN-LED3G

Display Type
TN - Twisted Nematic
Display Mode
Transflective
Number Of Digits/alpha
16
Outline L X W X H
108.00mm x 20.00mm x 12.00mm
Viewing Area
89.00mm L x 10.00mm W
Backlight
LED - Green
Display Format
40 x 2
Character Size
3.15mm H x 1.85mm W
Character Format
5 x 8 Dots
Voltage - Supply
5.0V
Dot Size
0.33mm W x 0.35mm H
Interface
Parallel
Operating Temperature
-20°C ~ 70°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
153-1129
DOCUMENT NUMBER AND REVISION
VL-FS-MDLS40263-01 REV.C
(MDLS40263-HT-HV-F-LED03-YG-12-CON)
DOCUMENT TITLE:
SPECIFICATION
OF
LCD MODULE TYPE
ITEM NO.: MDLS40263-01
PREPARED BY
CHECKED BY
FRANK WANG
APPROVED BY
DERRICK TAM
d

Related parts for MDLS-40263-C-HT-HV-FSTN-LED3G

MDLS-40263-C-HT-HV-FSTN-LED3G Summary of contents

Page 1

... DOCUMENT NUMBER AND REVISION VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) DOCUMENT TITLE: SPECIFICATION LCD MODULE TYPE ITEM NO.: MDLS40263-01 PREPARED BY CHECKED BY FRANK WANG APPROVED BY DERRICK TAM OF d ...

Page 2

... TO 0.0 2000.09.22 First Release 0 A 2002.03.01 Items were updated: (Based on the test specification VL-TS-MDLS40263-01 REV. A 2001.07.24). 1.)(Whole document) Number and format of pages were updated. 2.)(Page 1, Page 4) “Preliminary specification” was changed to “Specification”. 3.)(Page 8, point 4.2, table 5) Supply voltage (LCD), supply current (Logic & LCD) & ...

Page 3

... ENVIRONMENTAL CONDITION 4. ELECTRICAL SPECIFICATIONS 4.1 INTERFACE SIGNALS 4.2 TYPICAL ELECTRICAL CHARACTERISTICS 4.3 TIMING SPECIFICATIONS 4.4 TIMING DIAGRAM OF VDD AGAINST V0 4.5 CORRESPONDENCE BETWEEN CHARACTER CODES AND CHARACTER PATTERNS (NOVATEK STANDARD NT3881D-01) 5. REMARK 6. LCD COSMETIC CONDITIONS VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE CONTENTS Page No ...

Page 4

... Character size 1.85(W) x 3.15( dots) Character spacing 0.30(W) x 1.10(H) Character pitch 2.15(W) x 4.25(H) Dot size 0.33(W) x 0.35(H) Dot spacing 0.05(W) x 0.05(H) Dot pitch 0.38(W) x 0.38(H) Weight Approx: 30 VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Specification of LCD Module Type Item No.: MDLS40263-01 Table 1 Specifications Unit gram ...

Page 5

... VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Figure 1: Module specification ...

Page 6

... Ambient Temperature Humidity (Note1) Vibration (IEC 68-2-6) cells must be mounted on a suitable connector Shock (IEC 68-2-27) Half-sine pulse shape Note1: Product cannot sustain at extreme storage conditions for a long time. VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Table 2 Symbol VDD - VSS VLCD=VDD – V0 Vin ...

Page 7

... DB4 12 DB5 13 DB6 14 DB7 15 LED (+) 16 LED (-) VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Table 4 Ground (0V). Power supply for logic (+5V) Power supply for LCD driver Register Select Input: “High” for Data register (for read and write) “Low” for Instruction register (for write), ...

Page 8

... Wavelength of λ yellow-green LED03 backlight Luminance of backlight (on the backlight surface) Note 1: There is tolerance in optimum LCD driving voltage during production and it will be within the specified range. VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) PAGE Table 5 Symbol Conditions VDD =5.0V, Note1. “H” level IH1 “L” level IL1 “ ...

Page 9

... Parameter Enable cycle time Enable ”High” level pulse width Enable rise time Enable fall time RS, R/W set-up time RS, R/W address hold time Read data output delay Read data hold time VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Table 6 Symbol Min. Max. Unit ...

Page 10

... Figure 2: Bus write operation sequence (Writing data from MPU to NT3881). Figure 3: Bus read operation sequence (Reading out data from NT3881 to MPU). VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE ...

Page 11

... Timing Diagram of VDD against V0. Power on sequence shall meet the requirement of Figure 4, the timing diagram of VDD against V0. LOGIC SUPPLY VOLTAGE 0V OV LCD SUPPLY VOLTAGE VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE 95% 50ms(typical) Figure 4: Timing diagram of VDD against V0. VDD V0 ...

Page 12

... Correspondence between Character Codes and Character Patterns (NOVATEK Standard NT3881D-01) VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE ...

Page 13

... Remark VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE ...

Page 14

... Size: Large size (L): 1pcs/Laminate; Middle size (M): 2-6pcs/Laminate; Small size (S): >6pcs/Laminate. 6.5. Reference Document: 6.5.1 VL-QUA-084A 6.5.2 EI-WKL-980821-01 6.5.3 EI-LT-980225-01 6.6. Applicable Equpment: 6.6.1LCD Tester 6.7. Procedure 6.7.1 Definition of LCD parts: VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Effective Activated Area B : Viewing Area C : Outside V. Perimeter Seal E : Out Perimeter Seal F : Contact Leads ...

Page 15

... Excess Photo-resist Missing pattern Incomplete photo-resist Rainbow Uneven coating Black spot Contaminated by foreign materials Scratch Scratch on glass surface Mechanical damage on glass edge or Chip corner VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Scope Criterion Not accept Patterned area Not accept N/A Not accept Not accept pinhole ...

Page 16

... Seal epoxy bleeds into the EVA Bubble inside epoxy D Bag broken Vacuum bag broken N/A Misalignment Top & bottom fish eyes misaligned VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion Newton Ring can’t be found with unaided eyes under sodium lamp Scratch on EVA is not acceptable when it is observed under dark background with unaided eyes ...

Page 17

... Excess glass within mechanical dimension. Excess glass on contact lead Scribing on contact leads Wrong scribing Silver dot exposed VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion F, E Shape shall be accordant with specification Rework to remove the excess glass if possible ...

Page 18

... Seal epoxy bleeds into the EVA. Narrow seal width Color or hazy appearance neighboring to the end seal End seal epoxy does not entirely cover LC filling window. End seal depth exceed limit VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion A, B Length (mm) Width (mm) Acc No. / < ...

Page 19

... Polarizer bubble, Materials dent. White spot(for -ve mode) Lines, hairs Lines, hairs(for-ve model) Remark: 1. All above black spot/ foreign material defects min. space shall be≧20mm。 VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion A Large size glass: Cosmetic defect can’t be found at one meter distance to inspection and will not increase its size under electrical test ...

Page 20

... PI scraped Reverse twist Visible radialized spot Mechanical Chip on surface/ Damage side/ corner/ perimeter seal/ silver dot Chips on ledge, but not on ITO trace VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion A, B Refer to golden sample A, B Not accept any fingerprint A, B Refer to above Black spot/ Foreign ...

Page 21

... Ink misalignment defect The position of the ink shift. Thick or thin ink. Ink line/pattern are thicker or thinner than that specified in the drawing VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion F 1-X ≦ 1/2 width of single ITO 2-Y <1/10 length of ledge 3- Z <1/10 glass thickness。 ...

Page 22

... Scratch on reflective polarizer Scratch on transflective polarizer Folded line Mechanical damage Discoloration Wrong or reversed polarizer Polarizer shift or protrude from the edge of glass VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion A, B (a) Accept if thick or thin part is less than 10% or ≦0.15mm. (b) Reject if thick or thin part is more than 10% or ≧ ...

Page 23

... Defect Category Defect Description Polarizer defect Any peeling or delamination of polarizer Polarizer type not conform to the product specification Polarizer protecting film missing VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion N/A Not accept N/A Not accept N/A Not accept. (unless requested by customer) Drawing Specification ...

Page 24

... Dot Matrix Remark: 1. All above black spot/ foreign material defects min. space shall be≧20mm. VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion Refer to the spot and lines spec. A Large size﹕ ...

Page 25

... Pattern darker or lighter Darker/Lighter than standard sample at activated state. Current exceed designed High current value “Varitronix Limited reserves the right to change this specification.” FAX:(852) 2343-9555. URL:http://www.varitronix.com VL-FS-MDLS40263-01 REV.C (MDLS40263-HT-HV-F-LED03-YG-12-CON) JUN/2006 PAGE Zone Criterion N/A Not accept N/A Not accept Segment fatter than 110% or smaller than 90% of the designed value ...

Related keywords