T-52017D121J-FW-A-ABN Optrex America Inc, T-52017D121J-FW-A-ABN Datasheet
T-52017D121J-FW-A-ABN
Specifications of T-52017D121J-FW-A-ABN
Related parts for T-52017D121J-FW-A-ABN
T-52017D121J-FW-A-ABN Summary of contents
Page 1
... HANDLING PRECAUTIONS FOR TFT-LCD MODULE -- PACKGING SPECIFICATION -- PRODUCTS NUMBER LABELING FORMS -- LAMP UNIT FOR 12.1” SVGA T-52017D121J-FW-A-ABN (AB) No. 2005-0434 Approved by (Quality Assurance Division) Checked by (ACI Engineering Division) Prepared by (ACI Engineering Division) Item OPTREX CORPORATION First Edition Dec 12, 2005 Final Revision ...
Page 2
... APPLICATION This specification applies to color TFT-LCD module, T-52017D121J-FW-A-ABN. These specification papers are the proprietary product of OPTREX and include materials protected under copyright of OPTREX. No part of this document may be reproduced in any form or by any means without the express written permission of OPTREX. OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product specified in this document ...
Page 3
... OVERVIEW T-52017D121J-FW-A-ABN is 12.1” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit, and backlight unit. By applying 6 bit or 8 bit digital data, 800 × 600, 262 K-color or 16.7 M-color images are displayed on the 12.1” diagonal screen. Input power voltage is 3.3V for LCD driving. ...
Page 4
... Power Supply Voltages for LCD Power Supply Currents for LCD Permissive Input Ripple Voltage *1) Power and signals sequence: t1 ≤ < t2 ≤ < t3 ≤ 0.9VC C LCD Power Supply Logic Signal 0.1VCC Backlight Power Supply T-52017D121J-FW-A-ABN (AB) No. 2005-0434 SYMBOL VCC Note 1,2) op(Panel) T Note 2) ...
Page 5
... VCC-dip conditions should also follow the power and signals sequence. *2) Typical current condition: 64-gray-bar pattern 600 line mode VCC = +3 (2) Backlight ITEM Lamp Voltage Lamp Current Lamp Frequency Starting Lamp Voltage Lamp Life Time T-52017D121J-FW-A-ABN (AB) No. 2005-0434 td =37.9 kHz, f =60.0 Hz CLK SYMBOL MIN. TYP 540 IL 6 ...
Page 6
... The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature. *6) Please use the inverter which has symmetrical current wave form as follows, The degree of unbalance: less than 10% The ratio of wave height: less than CURRENT WAVE FORM T-52017D121J-FW-A-ABN (AB) No. 2005-0434 A CTL CTH CTH CTH ...
Page 7
... Recommended wiring of Pin 17,18 (6 bit input) LVDS transmitter LOW data (2) CN 2,3(Backlight) Backlight-side connector: BHR-04VS-1 (JST) Inverter-side connector: SM04(4.0)B-BHS-1(JST) Pin No. [ Note ] VBLH - VBLL = VL T-52017D121J-FW-A-ABN (AB) No. 2005-0434 8 bit input +3.3 V Power supply +3.3 V Power supply GND GND R2, R3, R4, R5, R6, R7, G2 R2, R3, R4, R5, R6, R7, G2 GND ...
Page 8
... ISP data mapping a. ISP 6 bit compatibility mode(6 bit input) CLKIN+/- Link0+/- Link1+/- Link2+/- b. ISP 6 bit compatibility mode(8 bit input) CLKIN+/- Link0+/- Link1+/- Link2+/- Link3+/- c. ISP 8 bit compatibility mode CLKIN+/- Link0+/- Link1+/- Link2+/- Link3+/- T-52017D121J-FW-A-ABN (AB) No. 2005-0434 DENA DENA DENA OPTREX CORPORATION ...
Page 9
... Active Time Blanking Time Vertical Frequency Period [Note] 1) DENA (Data Enable) should always be positive polarity as shown in the timing specification. 2) DCLK should appear during all invalid period. 3) LVDS timing follows the timing specifications of LVDS receiver IC: THC63LVDF84B(Thine). T-52017D121J-FW-A-ABN (AB) No. 2005-0434 SYMBOL MIN TYP CLK t 23 ...
Page 10
... Timing Chart a. Horizontal Timing Chart DCLK DATA Invalid Data (R,G, DENA b. Vertical Timing Chart LINE DATA Invalid Data t VB DENA T-52017D121J-FW-A-ABN (AB) No. 2005-0434 First Data =1 OPTREX CORPORATION Last Data 799 800 Invalid Data 599 600 Invalid Data t =1 Page 10/35 ...
Page 11
... MAGENTA 1 YELLOW 1 WHITE 1 RED(1) 0 RED(2) 0 RED RED(62) 1 RED(63) 1 GREEN(1) 0 GREEN(2) 0 GREEN GREEN(62) 0 GREEN(63) 0 BLUE(1) 0 BLUE(2) 0 BLUE BLUE(62) 0 BLUE(63) 0 [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-52017D121J-FW-A-ABN (AB) No. 2005-0434 R DATA LSB MSB ...
Page 12
... MAGENTA YELLOW WHITE RED( RED(2) RED RED(255 GREEN( GREEN(2) GREEN GREEN(255 BLUE( BLUE(2) BLUE BLUE(255) [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-52017D121J-FW-A-ABN (AB) No. 2005-0434 INPUT DATA R DATA G DATA LSB MSB ...
Page 13
... Display Position and Scan Direction D(X,Y) shows the data number of input signal for LCD panel signal processing PCB. SC:Low D(1,1) D(800,1) D(1,600) D(800,600) T-52017D121J-FW-A-ABN (AB) No. 2005-0434 SC:High D(800,600) CN2 D(800,1) CN3 OPTREX CORPORATION ...
Page 14
... BLOCK DIAGRAM CN1 Timing signal Display data Timing Converter Power Power Supply Circuit T-52017D121J-FW-A-ABN (AB) No. 2005-0434 G1 G2 TFT-LCD G600 Drivers(source) CCFL OPTREX CORPORATION CN2 , Page 14/35 ...
Page 15
... MECHANICAL SPECIFICATIONS (1) Front Side T-52017D121J-FW-A-ABN (AB) No. 2005-0434 OPTREX CORPORATION (Unit: mm) Page 15/35 ...
Page 16
... Rear Side [Note] We recommend you referring to the detailed drawing for your design. Please contact our company sales representative when you need the detailed drawing. T-52017D121J-FW-A-ABN (AB) No. 2005-0434 OPTREX CORPORATION (Unit:mm) Page 16/35 ...
Page 17
... Contrast Ratio, Luminance, Response Time, Viewing Angle, Color Coordinates: DisplayCenter Luminance Uniformity: point 1 ∼ 5 shown in a figure below *2) Definition of Contrast Ratio CR=Luminance with all white pixels / Luminance with all black pixels T-52017D121J-FW-A-ABN (AB) No. 2005-0434 Ta=25°C, VCC=3.3V, Input Signals: Typ. Values shown in Section 6 MIN CR θ ...
Page 18
... Continuously display the test pattern shown in the figure below for two-hours. Then display a completely white screen. The previous image shall not persist more than two seconds at 25°C. Rows 298-302 TEST PATTERN FOR IMAGE STICKING TEST T-52017D121J-FW-A-ABN (AB) No. 2005-0434 90% 10% Black tr , θ ...
Page 19
... The judgment of the above tests should be made as follow: Pass: Normal display image, no damage of the display function. (ex. no line defect) Partial transformation of the module parts should be ignored. Fail: No display image, damage of the display function. (ex. line defect) T-52017D121J-FW-A-ABN (AB) No. 2005-0434 40°C, 90%RH, 240 h BETWEEN –20°C (1h) and 80°C(1h), CONDITIONS ...