LQ104V1DG51 Sharp Microelectronics, LQ104V1DG51 Datasheet

LCD TFT 10.4" 640X480 VGA

LQ104V1DG51

Manufacturer Part Number
LQ104V1DG51
Description
LCD TFT 10.4" 640X480 VGA
Manufacturer
Sharp Microelectronics
Datasheet

Specifications of LQ104V1DG51

Display Type
LCD - Color
Display Mode
*
Viewing Area
211.20mm L x 158.40mm W
Dot Pixels
640 x 480 (VGA)
Pixel Density
640 x 480
Module Size (w X H X T)
246.5 mm x 179.4 mm x 15.5 mm
Backlighting
White Normally White
Diagonal
10.4 in
Viewing Area (w X H)
211.2 mm x 158.4 mm
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Interface
-
Backlight
-
Dot Size
-
Dot Pitch
-
Lead Free Status / Rohs Status
 Details
Other names
425-2470
P
S
RODUCT
PECIFICATIONS
AVC Liquid Crystal Displays Group
LQ104V1DG51
TFT-LCD Module
Spec. Issue Date: December 13, 2005
No: LD-13708D

Related parts for LQ104V1DG51

LQ104V1DG51 Summary of contents

Page 1

... P S RODUCT PECIFICATIONS LQ104V1DG51 TFT-LCD Module Spec. Issue Date: December 13, 2005 AVC Liquid Crystal Displays Group No: LD-13708D ...

Page 2

...

Page 3

... Application This specification applies to color TFT-LCD module, LQ104V1DG51 (This specification is only applied for the module which has letter "A" at the end of the lot number of the module.) These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...

Page 4

Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1.Note: excluding backlight cables. Outline dimensions is shown in Fig.1 Specifications 26 (10.4") Diagonal 211.2(H) 158.4(V) 640(H) ...

Page 5

Input Terminals 4-1. TFT-LCD panel driving 1 2 CN1 pin arrangement from module surface Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 Hsync Horizontal synchronous signal 4 Vsync Vertical synchronous signal 5 ...

Page 6

Note3 Note4 4-2. Backlight driving CN2,CN3 Pin no. Symbol 1 Power supply for lamp HIGH (High voltage side This is electrically opened. 3 Power supply for lamp LOW (Low voltage side) 5. Absolute Maximum Ratings Parameter Input voltage ...

Page 7

Electrical Characteristics 6-1.TFT-LCDpaneldriving Ta 25 Parameter Power Supply voltage Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) NOTE 1 Vcc-turn-on conditions Vcc-dip conditions Vcc-dip condition should also follow ...

Page 8

Backlight driving The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube). The characteristics of lamp are shown in the following table. (It is usually required to measure under the following condition. condition:IL=6.0mA,Ta=25 Parameter Symbol ...

Page 9

Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2 - 7-1. Timing characteristics Parameter Symbol Mode Clock Frequency 1/Tc High time Tch Low time Tcl Data Setup time Tds Hold time Tdh Horizontal Cycle ...

Page 10

Vertical display position The vertical display position is automatically centered in the active area at each mode of VGA ,480-,400-,and 350-line mode . Each mode is selected depending on the polarity of the synchronous signals described in 4-1(Note1). In ...

Page 11

...

Page 12

...

Page 13

...

Page 14

Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale R0 R1 Gray Scale Black 0 0 Blue 0 0 Green 0 0 Cyan 0 0 Red 1 1 Magenta 1 1 Yellow 1 ...

Page 15

Optical Characteristics Parameter Symbol Viewing Horizontal Angle Vertical Range Contrast ratio Response Rise Time Decay Chromaticity of White Luminance of white White Unifomity Viewing Horizontal Angle range as a Vertical Brightness Definition The measurement shall be executed 30 minutes ...

Page 16

Note1 Definitions of viewing angle range ’clo ck d irectio n Note2 Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) Note3 Definition of response time: The response time is defined as ...

Page 17

Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 11 Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable ...

Page 18

... Internal Use Only R.C. RoHS Compliance means these parts have corresponded with the RoHS directive. 2 Quantity LQ104V1DG51 . . ...

Page 19

...

Page 20

...

Page 21

This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...

Page 22

... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...

Related keywords