MTC600-ACNR16S1J Emerson Network Power, MTC600-ACNR16S1J Datasheet - Page 4

• Manufacturer Part Number: MTC600-ACNR16S1J
• Description: MODULE POWER 600W AC 16CH
• Manufacturer: Emerson Network Power
• Series: MTC600r

Specifications of MTC600-ACNR16S1J

• Voltage - Output: 3.63V, 12.95V
• Number Of Outputs: 2
• Power (watts): 600W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 90 ~ 264VAC
• Mounting Type: Rack Mount
• 1st Output: 12.95 VDC @ 7.6A
• 2nd Output: 3.63 VDC @ 250mA
• Size / Dimension: 7.37" L x 2.34" W x 2.89" H (187.2mm x 59.44mm x 73.4mm)
• Power (watts) - Rated: 600W
• Operating Temperature: -5°C ~ 45°C
• Approvals: CSA, CUL, UL, VDE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 454-1308

Electrical Specifications (continued)
Output - All Models (continued)
12 V Outputs (Payload Power)
Management Power Interdependence
Setpoint
Total Regulation Range
Rated Load
Minimum Load
Output Rise TIme (per channel)
Output Noise (PARD)
Output Voltage Overshoot
Transient Response
Voltage Sag
Short Circuit Protection
Channel Fault Operation
(Output to Return)
Channel Fault Operation
(Output to Output)
PS1# Extraction Delay
Reflected Ripple Tolerance on
Cooling Unit Outputs
Note 1: All channels and outputs must be confi gued by the carrier manager with the exception of MCH and CU channels and outputs
Note 2: All measurements are made at the output connector of the Power Module. Unless otherwise specifi ed,specs apply to all AMC,
Note 3: Measured with a 0.1 μF ceramic and 10 μF tantalum capacitor on any output and oscilloscope bandwidth set for 200 MHz.
Note 4: Consult with the factory if other outputs are expected to product signifi cant ripple current.
MCH, and CU outputs.
which are confi gured during Startup and/or autonomous operation,
3
4
1,2
is not affected. The other channels are not
12V Payload Power Output under fault is
shutdown. 3V3 MP on the same channel
12 V will not be applied without
No damage to Power Module
80 W / 7.6 A maximum
3% maximum deviation
3.3 V applied to a load
12.25 to 12.95 Vdc
11.60 to 12.00 Vdc
2 ms recovery time
100 mV maximum
600 W maximum
75 mV maximum
100 μs maximum
1.00 V maximum
25 ms maximum
10 ms maximum
12.6 Vdc typical
11.8 Vdc typical
9.7 A maximum
100 mV pk-pk
2% maximum
0.8 A pk-pk
affected
No load
Tolerance of Power Module to ripple generated
by fans or motors connected to Payload Power
onset of transient. Recovery time to within 1%
Time from de-assertion of PS1# to disabling of
maximum of 80 W load per output or 600 W
Primary PM to redundant PM transition with
the channel outputs and de-assertion of the
After removal of fault, the output channel is
Per Power Module, input voltage ≥110 Vac
available again under control of the Carrier
Referenced to load current and setpoint at
Manager. PM_OK# is not de-asserted and
Removal of 3.3 V also removes 12 V
Embedded Power for
Business-Critical Continuity
With 1600 μF on output under test
redundant failover is not initiated
shut down until fault is removed
No loss of regulation ≥110 Vrms
of setpoint at onset of transient
Configured as Redundant PM
Configured as Redundant PM
Either or both outputs may
Configured as Primary PM
Configured as Rrimary PM
and de-asserts ENABLE#
Referenced to setpoint
2 A loadstep @ 1 A/μs
Output to return
on Cooling Units
Per load channel
ENABLE# signal
0 to 100 MHz
0 to 30 MHz
load per PM
MTC600 Series
Rev. 05.26.08
4 of 19