HW-USB-FLYLEADS-G Xilinx Inc, HW-USB-FLYLEADS-G Datasheet
HW-USB-FLYLEADS-G
Specifications of HW-USB-FLYLEADS-G
Available stocks
Related parts for HW-USB-FLYLEADS-G
HW-USB-FLYLEADS-G Summary of contents
Page 1
R DS300 (v3.2) May 14, 2008 Features Platform Cable USB has these features: • Supported on Windows and Red Hat Enterprise Linux • Automatically senses and adapts to target I/O voltage • Interfaces to devices operating at 5V (TTL), 3.3V ...
Page 2
R Physical Description The Platform Cable USB electronics are housed in a recyclable, fire-retardant plastic case EMI shield attenuates internally generated emissions and protects against susceptibility to radiated emissions. X-Ref Target - Figure 2 R Platform Cable USB Top View ...
Page 3
R During a CPLD update, the Status LED illuminates red, and a progress bar indicates communication activity (see Figure 4). CPLD updates should never be interrupted. When an update is complete, the Status LED returns to either amber or green, ...
Page 4
R Found New Hardware Wizard (for Windows Only) Platform Cable USB should be disconnected from the host system during the initial software installation. The first time a cable is attached after software installation, Windows invokes the Found New Hardware wizard ...
Page 5
R Hot Plug and Play The cable can be attached and removed from the host computer without the need to power-down or reboot. There is a momentary delay after connecting the cable to an available port before the Status LED ...
Page 6
R In Boundary-Scan mode, iMPACT 7.1i (and later) queries the BSDL file of each device in a target Boundary-Scan chain to determine the maximum Boundary-Scan clock (JTAG TCK) frequency. iMPACT 7.1i (and later) automatically restricts the available TCK_CCLK_SCK selections to ...
Page 7
R X-Ref Target - Figure 11 Amber indicates no target voltage Green indicates target voltage present Figure 11: Status LEDs Indicating Target Voltage Suspend State Every USB device, including Platform Cable USB, can be placed into a Suspend state by ...
Page 8
R X-Ref Target - Figure 13 Figure 13: High-Performance Ribbon Cable Notes: 1. Ribbon Cable: 14 conductor, 1.0 mm center, round conductor flat cable, 28 AWG (7 x 36) stranded conductors, gray PVC with pin 1 edge marked ...
Page 9
R X-Ref Target - Figure 17 SPI NC NC MOSI MISO SCK SS V REF Figure 17: Target Interface Connector Dimensions and Signal Assignments Table 3: Mating Connectors for 2 mm Pitch, 14-Conductor Ribbon Cable (1) Manufacturer Molex FCI Comm ...
Page 10
R TDI_DIN_MOSI and TMS_PROG_SS Timing Specifications For JTAG, SPI, and slave-serial configuration modes, the TDI_DIN_MOSI and TMS_PROG_SS outputs change on falling edges of TCK_CCLK_SCK (Figure devices sample TDI_DIN_MOSI and TMS_PROG_SS on rising edges of TCK_CCLK_SCK. The minimum setup time T ...
Page 11
R X-Ref Target - Figure 19 Figure 19: TDO_DONE_MISO Timing with Respect to TCK_CCLK_SCK (CBL_TCK to TCK_CCLK_SCK Delay) X-Ref Target - Figure 20 Figure 20: TDO_DONE_MISO Timing with Respect to TCK_CCLK_SCK (TCK_CCLK_SCK to TDO_DONE_MISO Delay) X-Ref Target - Figure 21 ...
Page 12
R Target Reference Voltage Sensing (V Platform Cable USB incorporates an over-voltage clamp on the V pin of the 2 mm ribbon cable connector. The REF clamped voltage (V ) supplies a high-slew-rate buffer REF_A (NC7SZ125) that drives each of ...
Page 13
R Signal Integrity Platform Cable USB uses high-slew-rate buffers to drive TCK_CCLK_SCK, TMS_PROG_SS, and TDI_DIN_MOSI. Each buffer has a 30Ω series termination resistor. Users should pay close attention to PCB layout to avoid transmission line effects. Visit the Xilinx Central ...
Page 14
R X-Ref Target - Figure Connector (1) V CCAUX V 2 REF TDO 8 TDI 10 TMS 4 TCK 6 (2) GND X Notes: 1. Example implies that V same voltage. See device data sheets for appropriate ...
Page 15
R Hub Types and Cable Performance There are two important hub specifications that affect the performance of Platform Cable USB: maximum port current and total bandwidth. Maximum Port Current Platform Cable USB is a bus-powered device that draws less than ...
Page 16
R Interface Pin Descriptions Table 5: SS/JTAG/SPI Port: 14-Pin Ribbon Cable Connector Ribbon Slave-Serial JTAG Cable Configuration Configuration Number Mode Mode REF REF 4 PROG – 6 CCLK – 8 DONE – 10 DIN – 12 N/C ...
Page 17
R Table 5: SS/JTAG/SPI Port: 14-Pin Ribbon Cable Connector (Cont’d) Ribbon Slave-Serial JTAG Cable Configuration Configuration Number Mode Mode – – 9, 11, 13 Notes: 1. All odd pins ( 11, and ...
Page 18
R Table 8: AC Operating Characteristics Symbol Description T Clock Period CLK Cable Propagation Delay Time TDI_DIN_MOSI (TMS_PROG_SS) T CPD relative to the negative edge of TCK_CCLK_SCK @ 24 MHz Target Setup Time TDI_DIN_MOSI (TMS_PROG_SS) T TSU relative to the ...
Page 19
... DLC9 UH Part Number Low-power, RoHS-compliant Platform Cable USB. HW-USB-G Includes 1.8 meter A-B USB cable, 14-pin ribbon cable, flying wire adapter, and flying wires. HW-USB-FLYLEADS-G Additional flying wire adapter with wires. HW-RIBBON14 Additional 14-pin ribbon cable. www.xilinx.com Platform Cable USB Description Low-power, RoHS-compliant cable ...
Page 20
... Added marking information for the DLC9G, legacy DLC9LP, and original DLC9 cables to page • Updated the of the low-power, Pb-free DLC9G cable. • Updated all cable top labels and pictures with cable top labels with the new "Pb-free" HW-USB-G label. 08/24/07 3.1 Updated • ...