USB-ICP-SAB9 Future Designs Inc, USB-ICP-SAB9 Datasheet
USB-ICP-SAB9
Specifications of USB-ICP-SAB9
Related parts for USB-ICP-SAB9
USB-ICP-SAB9 Summary of contents
Page 1
... USB-ICP-SAB9 Quick Start Guide The USB-ICP-SAB9 is a Socket Adapter Board designed to be used with the USB In-Circuit Programmer for NXP Semiconductors LPC9xx devices. The SAB9 allows the user to program and test these microcontrollers outside of the application circuit. Throughout this document we will just refer to the SAB9 rather than using the complete part number since it simplifies the flow of information ...
Page 2
... USB-ICP-SAB9 socket layout: Each socket on the board is clearly labeled for the type of part that is programmed in it. When this document refers to the ‘top’ of the board, this is referring to the top of the board when the orientation shown in the picture above. USB-ICP-SAB9 Quick Start Guide Page Rev 1 ...
Page 3
... Connecting the USB-ICP-SAB9 to a USB-ICP To use the SAB9, it must first be connected through a USB-ICP with a USB-ICP-LPC9xx cable to P1, as shown above. Or, if you do not have the USB-ICP-LPC9xx, the SAB9 may be connected to the PC with regular Ethernet Patch cable to P2, as shown below. The USB-ICP must then be connected to the USB port on your PC ...
Page 4
... COM Port. Try raising or lowering the baud rate.” a. Make sure that you have the correct port selected and that the baud rate you have selected is the rate recommended for the USB-ICP USB-ICP-SAB9 Quick Start Guide Frequently Asked Questions Page www ...
Page 5
... P89LPC90x Devices in DIP8 Package: When placing any DIP8 Part in the SAB9 for programming, there must be 5 pins empty above and below the part being programmed. The pin one identifier (notch in chip) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT1 Page Rev 1 ...
Page 6
... P89LPC2x Devices in DIP20 Package: When placing any DIP20 Part in the SAB9 for programming, there must be 2 pins empty above and below the part being programmed. The pin one identifier (notch in chip) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT1 Page Rev 1 ...
Page 7
... Then, once the socket is ‘open’ drop the part into the socket and nudge it into place to match the documents below. When you release the sides of the socket the part will be locked in and ready for programming. USB-ICP-SAB9 Quick Start Guide Page ...
Page 8
... When placing any TSSOP14 Part in the SAB9 for programming, there must be 3 empty pins above and 4 empty pins below the part being programmed. The pin one identifier (circle in top left corner) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT2 Page Rev 1 ...
Page 9
... When placing any TSSOP16 Part in the SAB9 for programming, there must be 3 empty pins above and below the part being programmed. The pin one identifier (circle in top left corner) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT2 Page ...
Page 10
... When placing any TSSOP20 Part in the SAB9 for programming, there must be 2 pins empty above and below the part being programmed. The pin one identifier (circle in top left corner) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT2 Page ...
Page 11
... When placing any TSSOP28 Part in the SAB9 for programming, the part should take up the entire socket and there should be no empty pins. The pin one identifier (circle in top left corner) should be toward the top of the board. USB-ICP-SAB9 Quick Start Guide SKT2 Page Rev 1 ...
Page 12
... P89LPC910x Devices in HVSON10 Package: When placing any HVSON10 Part in the SAB9 for programming, the part should be turned so that the pin 1 identifier is in the upper left corner of the socket. USB-ICP-SAB9 Quick Start Guide SKT4 Page Rev 1.0 ...
Page 13
... P89LPC93x Devices in HVQFN28 Package: When placing any HVQFN28 Part in the SAB9 for programming, the part should be turned so that the pin 1 identifier is in the upper left corner of the socket. USB-ICP-SAB9 Quick Start Guide SKT3 Page Rev 1.0 ...
Page 14
... SAB9 so this function can be used on any package type. JP1 1-2: LED 2 connected to P0.6 JP1 2-3: LED 2 connected to P3.1 If you have any further questions, please contact FDI at support@teamfdi.com USB-ICP-SAB9 Quick Start Guide LED and Jumper function Page ...
Page 15
... USB-ICP-SAB9 Quick Start Guide Page Rev 1.0 ...