TOOLSTICK582DC Silicon Laboratories Inc, TOOLSTICK582DC Datasheet

Page 1

TICK 1. Handling Recommendations To enable development, the ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent damage to the ...

Page 2

To olSt ick-F 58 2DC 2. Contents The ToolStick-F582DC kit contains the ToolStick C8051F582 Daughter Card. A ToolStick daughter card requires a ToolStick Base Adapter to communicate with the PC. ToolStick Base Adapters can be purchased at www.silabs.com/toolstick. 3. ToolStick ...

Page 3

Getting Started The necessary software to download, debug, and communicate with the target microcontroller must be downloaded from www.silabs.com/toolstick. The following software is necessary to build a project, download code to, and communicate with the target microcontroller: Silicon Laboratories ...

Page 4

To olSt ick-F 58 2DC 5.2. Keil Demonstration Toolset 5.2.1. Keil Assembler and Linker The Keil demonstration toolset assembler and linker place no restrictions on code size. 5.2.2. Keil Demonstration C51 C Compiler The evaluation version of the C51 compiler ...

Page 5

Keil µVision2 and µVision3 Silicon Laboratories Drivers As an alternative to the Silicon Laboratories IDE, the µVision debug driver allows the Keil µVision2 and µVision3 IDEs to communicate with Silicon Laboratories on-chip debug logic. In-system Flash memory programming integrated ...

Page 6

To olSt ick-F 58 2DC 6. ToolStick C8051F582 Daughter Card Features Demo The ToolStick kit includes a few simple code examples. The example described in this section is titled F582DC_FeaturesDemo. The purpose of this example is to guide a new ...

Page 7

Connecting to the Device and Downloading Firmware This section describes how to open the IDE, open and build a project, connect to a device and download the firmware. 1. Open the Silicon Laboratories IDE from the Start  Programs ...

Page 8

To olSt ick-F 58 2DC 6.4. Viewing and Modifying Registers All registers on the device can be viewed and modified when the device halted state. The registers are grouped together according to which peripheral or part of ...

Page 9

Enabling and Using Watch Windows The Debug Windows in the View menu are used to view and modify hardware registers. To view and modify variables in code, the IDE provides Watch Windows. Just as with register debug windows, variables ...

Page 10

To olSt ick-F 58 2DC 6.6. Setting and Running to Breakpoints The Silicon Laboratories microcontroller devices support up to four hardware breakpoints. A breakpoint is associated with a specific line of code. When the processor reaches a hardware breakpoint, the ...

Page 11

Single-Stepping Through Firmware The IDE supports the ability to single-step through firmware one assembly instruction at a time. The IDE reads the Flash from the device, converts the instructions to assembly and displays them in a disassembly window. The ...

Page 12

To olSt ick-F 58 2DC 6.8. Using ToolStick Terminal This section describes how to use ToolStick Terminal to communicate with UART from the PC to the daughter card through the ToolStick Base Adapter the Silicon Laboratories IDE is ...

Page 13

The firmware on the C8051F582 target microcontroller does not need to be customized to use the UART and communicate with ToolStick Terminal. The firmware on the microcontroller should write to the UART as it would in any standard application and ...

Page 14

To olSt ick-F 58 2DC 10. C8051F582 Daughter Card Schematic 14 Rev. 0.1 ...

Page 15

N : OTES ToolStick-F582DC Rev. 0.1 15 ...

Page 16

... Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap- plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. ...