HS7145ECH61H Renesas Electronics America, HS7145ECH61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

... SH7145 Group FP-144F User System Interface Board HS7145ECH61H User’s Manual Renesas Microcomputer Development Environment System SuperH™ Family/SH7144 Series Rev.4.0 2004.01 ...

Page 4

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...

Page 5

... Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. User system interface cable (HS7145ECH61H) The user system or a host computer is not included in this definition. Purpose of the User System Interface Cable: This user system interface cable is for connecting the evaluation chip board and user system ...

Page 6

LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface cables determined to be defective in ...

Page 7

State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...

Page 8

READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL ...

Page 9

Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST not ...

Page 10

... The HS7145ECH61H is a user system interface board that connects a user system for the SH7145 FP-144F package to the SH7046 E6000H emulator (HS7046EPH60H). Preface i ...

Page 11

Section 1 Configuration.....................................................................................1 Section 2 Environmental Conditions.................................................................3 2.1 Setting Operating Voltage and Operating Frequency ....................................................... 3 Section 3 Product Specifications .......................................................................4 Drop in Vcc Level Detection Function: ............................................................................ 4 Section 4 User Interface Specifications .............................................................5 4.1 User System Interface Circuit ...

Page 12

Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-144F package. Please make sure you have all of these components when unpacking. Screws (M2 mm) Socket cover Figure 1 ...

Page 13

... User’s manual 2 CAUTION Quantity Remarks With two spacers (2.6MP For the FP-144F package (to be mounted on the user system) 1 For the FP-144F package (for installing MCU) 4 For fastening board 4 For installing an FP-144F-packaged MCU User’s manual for HS7145ECH61H (this manual) ...

Page 14

Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating 80% RH, no condensation Storage ...

Page 15

Section 3 Product Specifications The specifications of this product are shown in table 3. Table 3 Product Specifications Item Specifications Target processor SH7145F Package FP-144F Function Level limitation: This function keeps the output signal from 3-V emulator system equal to ...

Page 16

Section 4 User Interface Specifications The user system interface board incorporates a level conversion circuit supporting a low-voltage circuit. Accordingly, when connecting the user system to the emulator, pay attention to the signal delays and the number of FANINs and ...

Page 17

AVcc, AVss, AN7 to AN0, and AVref 5Vcc Emulator Emulator Vss Figure 5 User System Interface Circuit for AVcc, AVss, AN7 to AN0, and AVref (4) Other digital signals QSVcc Emulator Figure 6 User System Interface Circuit for Other ...

Page 18

UVcc and UVss QSVcc Vss Emulator Figure 7 User System Interface Circuit for UVcc and UVss Note: UVcc and UVss represent Vcc and Vss on a user system. 5Vcc and QSVcc represent Vcc generated in the user system interface ...

Page 19

Section 5 Connection Procedures 5.1 Connecting User System Interface Board to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make ...

Page 20

Installing Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-144F package on the user system with pin 1 on the user system interface board, and insert the user ...

Page 21

User system Figure 8 Connecting User System Interface Board to User System 10 Screws (M2 mm) Board Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) ...

Page 22

Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. ...

Page 23

Spacer User system Figure 9 Connecting User System Interface Board to EV-Chip Board 12 EV-chip board Connector No. EV-Chip Board Connector No. Board Board Connector No. UCN1 UCN1 UCN2 UCN2 ...

Page 24

Recommended Dimensions for User System Mount Pad (Footprint) Figure 10 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-144F package (NQPACK144SD: manufactured by Tokyo Eletech Corporation). Note that ...

Page 25

Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 11. Figure 11 Dimensions for EV-Chip Board and User System Interface Board 14 140.0 ...

Page 26

Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 12. Spacer ( 6.0) Figure 12 Resulting Dimensions after Connecting User System Interface ...

Page 27

Section 6 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If ...

Page 28

Screws (M2 mm) User system Figure 13 Installing MCU to User System Socket cover MCU (SH7145) Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) 17 ...

Page 29

Section 7 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7046 E6000H Emulator User's Manual (HS7046EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and ...

Page 30

To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 15 Installing the Clock Oscillator Enlarged view Crystal oscillator X1 X2 Evaluation chip ...

Page 31

Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned not apply excessive force to the user system interface board while it is connected to the user system. 3. ...

Page 32

... SH7145 Group FP-144F User System Interface Board HS7145ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2004 Renesas Technology Corp. All rights reserved. Printed in Japan. ...

Page 33

... User System Interface Board HS7145ECH61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan SH7145 Group FP-144F REJ10B0037-0400H ...