HS2128ECN61H Renesas Electronics America, HS2128ECN61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

...

Page 4

... H8S/2128 Series TQFP-80C User System Interface Cable (HS2128ECN61H) for E6000 Emulator User’s Manual Rev.1.0 1999.01 ...

Page 5

Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise ...

Page 6

... Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Hitachi, Ltd. excluding all subsidiary products. User system interface cable (HS2128ECN61H) The user system or a host computer is not included in this definition. Purpose of the User System Interface Cable: This user system interface cable is for connecting the emulator station and user system ...

Page 7

LIMITED WARRANTY Hitachi warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Hitachi will repair or replace any user system interface cables determined to be defective in ...

Page 8

State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...

Page 9

SAFETY PAGE • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION ...

Page 10

... Thank you for purchasing this user system interface cable (HS2128ECN61H) for the Hitachi’s original microcomputer H8S/2128 series. The HS2128ECN61H is a user system interface cable that connects an H8S/2148, H8S/2138, H8S/2128 series E6000 emulator (HS2148EPI60H; hereinafter referred to as the emulator) to the IC socket for a TQFP-80C package (package code: TFP-80C) for the H8S/2128 series MCU on the user system ...

Page 11

Section 1 Configuration ................................................................................................... 1 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 3 2.2 Connecting User System Interface Cable to User System................................................ 4 2.2.1 Installing IC Socket ............................................................................................. 4 2.2.2 Soldering IC Socket............................................................................................. ...

Page 12

... Section 1 Configuration Use an IC149-080-058-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C package IC socket on the user system. Figure 1 shows the configuration of the HS2128ECN61H user system interface cable for the TFP-80C package. Figure 1 HS2128ECN61H User System Interface Cable CAUTION 1 ...

Page 13

... Table 1 lists the HS2128ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2128ECN61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws (M2 mm) 6 Screws (M2 mm) 7 Documentation 2 Quantity Remarks 1 Includes two flat cables 1 1 For the TFP-80C package ...

Page 14

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make ...

Page 15

Figure 2 Connecting User System Interface Cable to Emulator Station 2.2 Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed ...

Page 16

Soldering IC Socket After fastening, solder the IC socket for an TFP-80C package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly ...

Page 17

Fasten the user system interface cable head to the IC socket for an TFP-80C package on the user system with the four screws (M2.6 be tightened a little at a time, alternating between screws on opposing corners. Take special care, ...

Page 18

Fastening Cable Body 1. Open the cable holder at the cable head. 2. Placing the cable body so it fits inside the cable holder, connect the cable body to the cable head. 3. Close the cable holder to prevent ...

Page 19

Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an TFP-80C package (IC149-080-058-B51: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that ...

Page 20

Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 9 ...

Page 21

Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 10 ...

Page 22

Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If ...

Page 23

Figure 8 Installing MCU to User System 12 ...

Page 24

Section 4 Verifying Operation 1. When using the E6000 emulator (HS2148EPI60H) for the H8S/2148, H8S/2138, H8S/2128 series, turn on the emulator according to the procedures described in the H8S/2148, H8S/2138, H8S/2128 Series E6000 Emulator User's Manual (HS2148EPI60HE). 2. Verify the ...

Page 25

Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...