HS7018EWN61H Renesas Electronics America, HS7018EWN61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

To all our customers Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp. The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April ...

Page 4

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...

Page 5

... SH7018 Series TFP-100B User System Interface Cable (HS7018EWN61H) for E6000 Emulator User’s Manual Rev.1.0 2002.07 ...

Page 6

Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with ...

Page 7

... Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Hitachi, Ltd. excluding all subsidiary products. User system interface cable (HS7018EWN61H) The user system or a host computer is not included in this definition. Purpose of the User System Interface Cable: This user system interface cable is for connecting the emulator station and user system ...

Page 8

LIMITED WARRANTY Hitachi warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Hitachi will repair or replace any user system interface cables determined to be defective in ...

Page 9

State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...

Page 10

READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL ...

Page 11

Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST not ...

Page 12

... Thank you for purchasing this user system interface cable (HS7018EWN61H) for the Hitachi’s original microcomputer SH7018 series. The HS7018EWN61H is a user system interface cable that connects an SH7010 series E6000 emulator (HS7010EPI60H; hereinafter referred to as the emulator) to the IC socket for a TFP- 100B package for the SH7018 series MCU on the user system ...

Page 13

Section 1 Configuration....................................................................................1 Section 2 Environmental Conditions.................................................................3 2.1 Setting Operating Voltage and Operating Frequency ....................................................... 3 Section 3 Product Specifications .......................................................................4 Section 4 User Interface Specifications .............................................................5 4.1 User System Interface Circuit ........................................................................................... 5 Section 5 Notes on Emulation ...........................................................................8 ...

Page 14

... Section 1 Configuration Use an IC149-100-054-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-100B package IC socket on the user system. Figure 1 shows the configuration of the HS7018EWN61H user system interface cable for the TFP-100B package. Figure 1 HS7018EWN61H User System Interface Cable CAUTION 1 ...

Page 15

... Table 1 lists the HS7018EWN61H components. Please make sure you have all of these components when unpacking. Table 1 HS7018EWN61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws (M2 mm) 6 Screws (M2 mm) 7 Documentation 2 Quantity Remarks For the TFP-100B package 1 For installing a TFP-100B-packaged MCU ...

Page 16

Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating 80% RH, no condensation Storage ...

Page 17

Section 3 Product Specifications The specifications of this product are shown in table 3. Table 3 Product Specifications Item Specifications Target processor SH7018F Package TFP-100B Function Level limitation: This function keeps the output signal from 5-V emulator system equal to ...

Page 18

Section 4 User Interface Specifications The user system interface cable incorporates a level conversion circuit supporting a low-voltage circuit. Accordingly, when connecting the user system to the emulator, pay attention to the signal delays and the number of FANINs and ...

Page 19

AVcc, AVss, and AN7 to AN0 Emulator Vss Figure 5 User System Interface Circuit for AVcc, AVss, and AN7 to AN0 (4) PVcc, Vcc and Vss To internal circuit 5Vcc of user system interface cable OR circuit Vss Emulator ...

Page 20

Note: 5Vcc, Uvcc, and Uvss represent Vcc and Vss on a user system. 5Vcc represents Vcc (5 V) generated in the user system interface cable. 7 ...

Page 21

Section 5 Notes on Emulation This user system interface cable supports the SH7018F. The following settings must be made prior to emulation. 5.1 Setting Internal ROM Set 32 kbytes for internal ROM size. Even when 32 kbytes is set for ...

Page 22

Section 6 Connection Procedures 6.1 Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will ...

Page 23

Figure 8 Connecting User System Interface Cable to Emulator Station 10 ...

Page 24

Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 ...

Page 25

Inserting Cable Head Check the location of pin 1 before inserting. If the IC socket is not connected properly, the power-supply pins will be shorted as shown below. 90˚ rotation 25 (Vss) 100 (Vcc) 55 (PVcc) 30 (Vcc) 99 ...

Page 26

Fasten the user system interface cable head to the IC socket for a TFP-100B package on the user system with the four screws (M2.6 be tightened a little at a time, alternating between screws on opposing corners. Take special care, ...

Page 27

Fastening Cable Body Connect the cable body to the cable head. 14 Figure 10 Fastening Cable Body ...

Page 28

Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-100B package (IC149-100-054-B51: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that ...

Page 29

Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 12. Figure 12 Dimensions for User System Interface Cable Head 16 ...

Page 30

Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 13. Figure 13 Resulting Dimensions after Connecting User System Interface Cable 17 ...

Page 31

Section 7 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If ...

Page 32

Figure 14 Installing MCU to User System 19 ...

Page 33

Section 8 Verifying Operation 1. When using the E6000 emulator for the SH series, turn on the emulator according to the procedures described in the SH Series E6000 Emulator User’s Manual (HS7000EPI60HE). 2. Verify the user system interface cable connections ...

Page 34

Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...