PA-SOF-D420-16/1 Logical Systems Inc., PA-SOF-D420-16/1 Datasheet

no-image

PA-SOF-D420-16/1

Manufacturer Part Number
PA-SOF-D420-16/1
Description
ADAPTER 16 PIN .420" PLUGS
Manufacturer
Logical Systems Inc.
Datasheet

Specifications of PA-SOF-D420-16/1

Module/board Type
*
For Use With/related Products
-
Other names
Q2777361A
DIP to SO-Plug Prototyping Adapters
DIP to SO-Plug Prototyping Adapters
DIP to SO-Plug Prototyping Adapters
Simplify prototyping and testing
Use actual size prototype boards
Great for microcontrollers and EE/Flash memory testing
Simple design is easy to use
These plugs and socket boards are simple and easy to use following
this 3 step process.
1. Solder the SO-Plug to the prototype's SO land pattern.
Use your preferred soldering technique to attach the SO-Plug to the
board's land pattern.
Hand soldering tip. Select either a very fine tip or a large tip with sharp angles. The sharp angles exploit the solder's surface tension to
prevent solder bridges. Heat up the iron. Carefully align the plug on the land pattern. Solder the plug leads in opposite corners. Start at an
unsoldered end pin. Using the capillary action of the tip, sweep down the row of pins. Wet each pin with solder then use the iron to pull the
excess solder away from the pin.
2. Plug the DIP board onto the SO-Plug's header pins.
Note the pin one ends of the land pattern and the DIP Board. Align the SO-Plug's pins with the receptacles of the DIP Board.
Press together until the pins bottom out in the receptacle. Some SO-Plugs will leave exposed pin between the receptacle and
the SO-Plug’s insulator.
3. Plug the emulator or erasable device into the DIP board.
The DIP Board provides either a production socket or ZIF socket for access to the prototype. Plug the device or development
tool into the socket and start testing.
Product Selection
Use the Logical Systems cross reference to identify the correct SO-Plug for the SO device you are using. If your device is not in
the cross reference, compare your prototype’s land pattern to the recommended land patterns for each size plug. Select the Kit
or component packs that fit your needs from the list below. The cross reference also provides the recommended DIP pattern for
the device you are using. Confirm the DIP pin count and row spacing with your emulator or prototyping devices.
39
Tel: 315.478.0722
Fax: 315.479.6753
Email: info@logicalsys.com
www.logicalsys.com

Related parts for PA-SOF-D420-16/1

PA-SOF-D420-16/1 Summary of contents

Page 1

... Hand soldering tip. Select either a very fine tip or a large tip with sharp angles. The sharp angles exploit the solder's surface tension to prevent solder bridges. Heat up the iron. Carefully align the plug on the land pattern. Solder the plug leads in opposite corners. Start at an unsoldered end pin ...

Page 2

... PA-DSO-2806(Z)-D560-28/2 PA-DSO-3206(Z)-D560-32/2 PA-DSO-4406(Z)-D560-40/2 PA-DSO-4406(Z)-D560-44/2 If the combination you want is not listed Other pin counts, lead spans and boards can be created to meet your needs. Contact us for pricing and availability. (www = plug width & pin count) 560 mil wide 630 mil wide ...

Page 3

... Email: info@logicalsys.com www.logicalsys.com DIP Boards Boards are available in sizes from 8-44 and in two widths with optional ZIF (Z) sockets. The board below is available in 8, 16, 18, 20, 24, and 28 pins. Part number format = PA-DSO-bbbb(Z) The board below is available in 28, 32 and 44 pins. Part number format = PA-DSO-bbbb(Z) 41 ...

Related keywords