STEVAL-PCC010V1 STMicroelectronics, STEVAL-PCC010V1 Datasheet - Page 19

no-image

STEVAL-PCC010V1

Manufacturer Part Number
STEVAL-PCC010V1
Description
BOARD EVAL FOR ST802RT1
Manufacturer
STMicroelectronics

Specifications of STEVAL-PCC010V1

Main Purpose
Interface, Ethernet Controller (PHY and MAC)
Embedded
Yes, MCU, 8-Bit
Utilized Ic / Part
ST802RT1
Primary Attributes
1 Port, 100BASE-TX/10BASE-T
Secondary Attributes
MII, RMII
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-10360

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STEVAL-PCC010V1
Manufacturer:
STMicroelectronics
Quantity:
3
ST802RT1A, ST802RT1B
Table 10.
Bit
7
6
5
4
3
2
1
0
Collision test
RESERVED Not used
RESERVED Not used
RESERVED Not used
RESERVED Not used
RESERVED Not used
RESERVED Not used
RESERVED Not used
Bit name
RN00 [0d00, 0x00]: Control register (continued)
Soft reset: In order to reset the ST802RT1x by software control, a “1” must be written to bit
15 of the control register using a serial management interface write operation. The bit clears
itself after the reset process is complete, and does not need to be cleared using a second
MII write. Writes to other control register bits have no effect until the reset process is
completed, which requires approximately 1 millisecond. Writing a “0” to this bit has no effect.
Since this bit is self-clearing, after a few cycles from a write operation, it returns a “0” when
read.
Local loop-back: The ST802RT1x may be placed into loop-back mode by writing a “1” to
bit 14 of the control register. The loop-back mode may be cleared by writing a “0” to bit 14 of
the control register, or by resetting the chip. When this bit is read, it returns a “1” when the
chip is in software-controlled loop-back mode; otherwise it returns a “0”.
Speed selection: If auto-negotiation is enabled, this bit has no effect on the speed
selection. However, if auto-negotiation is disabled by software control, the operating speed
of the ST802RT1x can be forced by writing the appropriate value to bit 13 of the control
register. Writing a “1” to this bit forces 100BASETX operation, while writing a “0” forces
10BASE-T operation. When this bit is read, it returns the value of the software-controlled
forced speed selection only.
Auto-negotiation enable: Auto-negotiation can be disabled by one of two methods:
hardware or software control. If the AN_EN input pin is driven to “0”, auto-negotiation is
disabled by hardware control. If bit 12 of the control register is written with a value of “0”,
auto-negotiation is disabled by software control. When auto-negotiation is disabled in this
manner, writing a “1” to the same bit of the control register re-enables auto-negotiation. If
auto-negotiation is disabled in this manner and the chip is reset the auto-negotiation follows
the strap configuration. Writing to this bit has no effect when auto-negotiation has been
disabled by hardware control. When read, this bit returns the value most recently written to
this location, or “1” if it has not been written since the last chip reset.
Power-down: If set to '1', the channel is powered down. If this bit is set for all channels, then
the IO pad directions are forced and the device is in power-down state. Refer to
for a more detailed explanation of the power-down operation.
Isolate: The PHY may be isolated from its media independent interface (MII) by writing a
“1” to bit 10 of the control register. All MII outputs are tri-stated, except tx_clk, and all MII
inputs are ignored. Since the MII management interface is still active, the isolate mode may
1 -> Collision test enabled
0 -> Normal operation
Active only in loop-back mode (RN00[14]=1)
Description
Doc ID 17049 Rev 1
Registers and descriptors description
Default
0
0
0
0
0
0
0
0
type
RW
RW
RO
RO
RO
RO
RO
RO
RO
Section 7.9
Type
19/58
P
P
P
P
P
P
P
-

Related parts for STEVAL-PCC010V1