ISL54205BEVAL1Z Intersil, ISL54205BEVAL1Z Datasheet

no-image

ISL54205BEVAL1Z

Manufacturer Part Number
ISL54205BEVAL1Z
Description
EVALUATION BOARD FOR ISL54205B
Manufacturer
Intersil
Datasheets

Specifications of ISL54205BEVAL1Z

Main Purpose
Interface, Analog & Digital Switch
Embedded
No
Utilized Ic / Part
ISL54205
Primary Attributes
2 x SPDT Audio & USB Switch
Secondary Attributes
2.7 V ~ 3.6 V Supply
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MP3/USB 2.0 High Speed Switch with
Negative Signal Handling
The Intersil ISL54205B dual SPDT (Single Pole/Double
Throw) switches combine low distortion audio and accurate
USB 2.0 high speed data (480Mbps) signal switching in the
same low voltage device. When operated with a 2.7V to 3.6V
single supply these analog switches allow audio signal swings
below-ground, allowing the use of a common USB and audio
headphone connector in Personal Media Players and other
portable battery powered devices.
The ISL54205B incorporates circuitry for detection of the USB
V
USB signal sources in the portable device. The part has a
control pin to open all the switches and put the part in a low
power down state.
The ISL54205B is available in a small 10 Ld 2.1mmx1.6mm
ultra-thin
package. It operates over a temperature range of -40 to
+85°C.
Related Literature
• Application Note AN1280 “ISL54205EVAL1Z Evaluation
• Technical Brief TB363 “Guidelines for Handling and
• Application Note AN557 “Recommended Test Procedures
Application Block Diagram
BUS
Board User’s Manual.
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
for Analog Switches”
voltage, which is used to switch between the audio and
µ
TQFN package and a 10Ld 3mmx3mm TDFN
®
1
22kΩ
Data Sheet
COM -
COM +
V
BUS
LOGIC CIRCUITRY
4MΩ
ISL54205B
1-888-INTERSIL or 1-888-468-3774
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
V
GND
DD
4MΩ
50kΩ
50kΩ
Features
• High Speed (480Mbps) and Full Speed (12Mbps)
• Low Distortion Negative Signal Capability
• Detection of V
• Control Pin to Open all Switches and Enter Low Power
• Low Distortion Headphone Audio Signals
• Cross-talk (20Hz to 20kHz) . . . . . . . . . . . . . . . . . . -110dB
• Single Supply Operation (V
• -3dB Bandwidth USB Switch . . . . . . . . . . . . . . . . . 630MHz
• Available in
• Pb-Free (RoHS Compliant)
• Compliant with USB 2.0 Short Circuit Requirements
Applications
• MP3 and Other Personal Media Players
• Cellular/Mobile Phones
• PDA’s
• Audio/USB Switching
September 25, 2007
Signaling Capability per USB 2.0
State
- THD+N at 20mW into 32Ω Load . . . . . . . . . . . . . <0.1%
Without Additional External Components
CTRL
D-
D+
R
L
All other trademarks mentioned are the property of their respective owners.
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
µ
TQFN and TDFN Packages
BUS
Copyright Intersil Americas Inc. 2007. All Rights Reserved
Voltage on USB Cable
µCONTROLLER
TRANSCEIVER
HIGH-SPEED
DD
CODEC
USB
) . . . . . . . . . . . . 2.7V to 3.6V
ISL54205B
FN6557.0

Related parts for ISL54205BEVAL1Z

ISL54205BEVAL1Z Summary of contents

Page 1

... All other trademarks mentioned are the property of their respective owners. ISL54205B FN6557.0 Voltage on USB Cable BUS ) . . . . . . . . . . . . 2.7V to 3.6V DD TQFN and TDFN Packages µ µCONTROLLER USB HIGH-SPEED TRANSCEIVER CODEC | Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007. All Rights Reserved ...

Page 2

... These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. ...

Page 3

Pin Descriptions PIN NUMBER NAME 1 VDD 2 VBUS 3 COM- 4 COM+ 5 GND CTRL 3 ISL54205B FUNCTION Power Supply Digital Control Input Voice and Data Common Pin Voice and ...

Page 4

... Maximum Junction Temperature (Plastic Package +150° 0.3V) Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C DD Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below ) + 0.3V) http://www.intersil.com/pbfree/Pb-FreeReflow.asp DD Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C exceeding V or GND by specified amount are clamped. Limit current to maximum current ...

Page 5

Electrical Specifications - 2.7V to 3.6V Supply PARAMETER r Matching Between Channels Δ COMx (Note 11) r Flatness FLAT(ON COMx OFF Leakage Current D+(OFF ...

Page 6

Electrical Specifications - 2.7V to 3.6V Supply PARAMETER CTRL Voltage High CTRLH DD Input Current BUSL CTRLL DD Input Current BUSH DD Input Current CTRLH DD V Pull-Down Resistor, R ...

Page 7

Test Circuits and Waveforms V BUSH LOGIC INPUT V BUSL V OUT SWITCH OUTPUT 0V FIGURE 2A. MEASUREMENT POINTS /100mA ON 1 CTRL 100mA COMX GND Repeat test ...

Page 8

Test Circuits and Waveforms CTRL AUDIO OR USB IMPEDANCE ANALYZER COMx GND Repeat test for all switches. FIGURE 5. CAPACITANCE TEST CIRCUIT t ri 90% 50% 10% DIN+ t skew_i DIN- 90% 50% 10 90% 10% ...

Page 9

Application Block Diagram 22kΩ Detailed Description The ISL54205B device is a dual single pole/double throw (SPDT) analog switch device that operates from a single DC power supply in the range of 2.7V to 3.6V. It was designed to function as ...

Page 10

USB 2.0 high speed signal quality specifications. See high-speed eye diagram in the “Typical Performance Curves” on page 12, Figure 12. The USB switches can also pass USB full-speed signals (12Mbps) with minimal ...

Page 11

Typical Performance Curves 0. 32Ω LOAD V = 0.707V LOAD RMS 0.10 0. 2.6V DD 0.08 0. 2. 0.05 0.04 20 200 FREQUENCY (Hz) FIGURE 8. THD+N vs ...

Page 12

Typical Performance Curves FIGURE 12. EYE PATTERN: 480Mbps WITH SWITCH IN THE SIGNAL PATH 12 ISL54205B T = +25°C, Unless Otherwise Specified (Continued) A TIME SCALE (10ns/DIV) FN6557.0 September 25, 2007 ...

Page 13

Typical Performance Curves FIGURE 13. EYE PATTERN: 12MBps WITH SWITCHES IN THE SIGNAL PATH 13 ISL54205B T = +25°C, Unless Otherwise Specified (Continued) A TIME SCALE (10ns/DIV 3.3V DD FN6557.0 September 25, 2007 ...

Page 14

Typical Performance Curves 50Ω 0. P-P P-P 1M 10M FREQUENCY (Hz) FIGURE 14. FREQUENCY RESPONSE 14 ISL54205B T = +25°C, Unless Otherwise Specified (Continued) A Die ...

Page 15

... Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: TERMINAL TIP No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. L MILLIMETERS MIN NOMINAL MAX A 0 ...

Page 16

... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...

Related keywords