C8051F330DK Silicon Laboratories Inc, C8051F330DK Datasheet - Page 69

• Manufacturer Part Number: C8051F330DK
• Description: DEV KIT FOR C8051F330/F331
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F330DK

• Contents: Evaluation Board, Power Supply, USB Cables, Adapter and Documentation
• Processor To Be Evaluated: C8051F33x
• Interface Type: RS-232
• Operating Supply Voltage: 7 V to 15 V
• Silicon Manufacturer: Silicon Labs
• Core Architecture: 8051
• Silicon Core Number: C8051F330
• Silicon Family Name: C8051F33x
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: Silicon Laboratories C8051F330, C8051F331
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1264

C8051F330/1/2/3/4/5
With the CIP-51's maximum system clock at 25 MHz, it has a peak throughput of 25 MIPS. The CIP-51 has
a total of 109 instructions. The table below shows the total number of instructions that require each execu-
tion time.
Programming and Debugging Support
In-system programming of the Flash program memory and communication with on-chip debug support
logic is accomplished via the Silicon Labs 2-Wire Development Interface (C2). Note that the re-program-
mable Flash can also be read and changed a single byte at a time by the application software using the
MOVC and MOVX instructions. This feature allows program memory to be used for non-volatile data stor-
age as well as updating program code under software control.
The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints, starting, stopping and single stepping through program execution (including interrupt service
routines), examination of the program's call stack, and reading/writing the contents of registers and mem-
ory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or
other on-chip resources. C2 details can be found in
The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs pro-
vides an integrated development environment (IDE) including editor, macro assembler, debugger and pro-
grammer. The IDE's debugger and programmer interface to the CIP-51 via the C2 interface to provide fast
and efficient in-system device programming and debugging. Third party macro assemblers and C compil-
ers are also available.
9.1.
The instruction set of the CIP-51 System Controller is fully compatible with the standard MCS-51™ instruc-
tion set. Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51
instructions are the binary and functional equivalent of their MCS-51™ counterparts, including opcodes,
addressing modes and effect on PSW flags. However, instruction timing is different than that of the stan-
dard 8051.
9.1.1. Instruction and CPU Timing
In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with
machine cycles varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based
solely on clock cycle timing. All instruction timings are specified in terms of clock cycles.
Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock
cycles as there are program bytes in the instruction. Conditional branch instructions take one less clock
cycle to complete when the branch is not taken as opposed to when the branch is taken. Table 9.1 is the
CIP-51 Instruction Set Summary, which includes the mnemonic, number of bytes, and number of clock
cycles for each instruction.
9.1.2. MOVX Instruction and Program Memory
The MOVX instruction is typically used to access external data memory (Note: the C8051F330/1/2/3/4/5
does not support off-chip data or program memory). In the CIP-51, the MOVX instruction can be used to
access on-chip XRAM or on-chip program memory space implemented as re-programmable Flash mem-
ory. The Flash access feature provides a mechanism for the CIP-51 to update program code and use the
72
Number of Instructions
Clocks to Execute
Instruction Set
26
1
50
2
2/3
Rev. 1.7
5
Section “20. C2 Interface” on page
14
3
3/4
7
4
3
4/5
1
209.
5
2
8
1