AD9517-4/PCBZ Analog Devices Inc, AD9517-4/PCBZ Datasheet - Page 43

• Manufacturer Part Number: AD9517-4/PCBZ
• Description: BOARD EVALUATION AD9517-4
• Manufacturer: Analog Devices Inc

Specifications of AD9517-4/PCBZ

• Design Resources: High Performance, Dual Channel IF Sampling Receiver (CN0140)
• Main Purpose: Timing, Clock Generator
• Utilized Ic / Part: AD9517-4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Divider
0
1
Phase Offset or Coarse Time Delay (0, 1)
Each channel divider allows for a phase offset, or a coarse time
delay, to be programmed by setting register bits (see Table 38).
These settings determine the number of cycles (successive
rising edges) of the channel divider input frequency by which to
offset, or delay, the rising edge of the output of the divider. This
delay is with respect to a nondelayed output (that is, with a
phase offset of zero). The amount of the delay is set by five bits
loaded into the phase offset (PO) register plus the start high (SH)
bit for each channel divider. When the start high bit is set, the
delay is also affected by the number of low cycles (M)
programmed for the divider.
The SYNC function must be used to make phase offsets effective
(see the Synchronizing the Outputs—SYNC Function section).
Table 38. Setting Phase Offset and Division for Divider 0 and
Divider 1
Let
Δt = delay (in seconds).
Δc = delay (in cycles of clock signal at input to D
T
(in seconds).
Φ = 16 × SH[4] + 8 × PO[3] + 4 × PO[2] + 2 × PO[1] + 1 × PO[0]
The channel divide-by is set as N = high cycles and M = low cycles.
Case 1
For Φ ≤ 15:
Δt = Φ × T
Δc = Δt/T
Case 2
For Φ ≥ 16:
Δt = (Φ − 16 + M + 1) × T
Δc = Δt/T
By giving each divider a different phase offset, output-to-output
delays can be set in increments of the channel divider input
clock cycle. Figure 54 shows the results of setting such a coarse
offset between outputs.
X
DIVIDER 0
DIVIDER 1
DIVIDER 2
= period of the clock signal at the input of the divider, D
DIVIDER INPUT
CHANNEL
X
SH = 0
PO = 0
SH = 0
PO = 1
SH = 0
PO = 2
Start
High (SH)
0x191[4]
0x197[4]
X
X
= Φ
Figure 54. Effect of Coarse Phase Offset (or Delay)
0
1
Tx
2
Phase
Offset (PO)
0x191[3:0]
0x197[3:0]
3
1 × Tx
2 × Tx
4
X
5
6
7
Low Cycles
M
0x190[7:4]
0x196[7:4]
8
9 10 11 12 13 14 15
X
).
High Cycles
N
0x190[3:0]
0x196[3:0]
X
Rev. B | Page 43 of 80
Channel Dividers—LVDS/CMOS Outputs
Channel Divider 2 and Channel Divider 3 each drive a pair of
LVDS outputs, giving four LVDS outputs (OUT4 to OUT7).
Alternatively, each of these LVDS differential outputs can be
configured individually as a pair (A and B) of CMOS single-
ended outputs, providing for up to eight CMOS outputs. By
default, the B output of each pair is off but can be turned on as
desired.
Channel Divider 2 and Channel Divider 3 each consist of two
cascaded, 2 to 32, frequency dividers. The channel frequency
division is D
bypassing one or both of these dividers. Both of the dividers
also have DCC enabled by default, but this function can be
disabled, if desired, by setting the DCCOFF bit of the channel.
A coarse phase offset or delay is also programmable (see the
Phase Offset or Coarse Time Delay (Divider 2 and Divider 3)
section). The channel dividers operate up to 1600 MHz. The
features and settings of the dividers are selected by programming
the appropriate setup and control registers (see Table 52 and
Table 53 through Table 62).
Table 39. Setting Division (D
Divider
2
3
1
Channel Frequency Division (Divider 2 and Divider 3)
The division for each channel divider is set by the bits in the
registers for the individual dividers (X.Y = 2.1, 2.2, 3.1, and 3.2)
When both X.1 and X.2 are bypassed, D
When only X.2 is bypassed, D
When both X.1 and X.2 are not bypassed, D
(N
By cascading the dividers, channel division up to 1024 can be
obtained. However, not all integer value divisions from 1 to
1024 are obtainable; only the values that are the product of the
separate divisions of the two dividers (D
If only one divider is needed when using Divider 2 and Divider 3,
use the first one (X.1) and bypass the second one (X.2). Do not
bypass X.1 and use X.2.
Note that the value stored in the register = # of cycles minus 1.
X.2
Number of Low Cycles = M
Number of High Cycles = N
2.1
2.2
3.1
3.2
+ M
X.2
M
0x199[7:4]
0x19B[7:4]
0x19E[7:4]
0x1A0[7:4]
+ 2).
X.1
× D
X.2
or up to 1024. Divide-by-1 is achieved by
N
0x199[3:0]
0x19B[3:0]
0x19E[3:0]
0x1A0[3:0]
X
X
= (N
) for Divider 2, Divider 3
X.Y
X.Y
+ 1
+ 1
X.1
X.1
+ M
X
Bypass
0x19C[4]
0x19C[5]
0x1A1[4]
0x1A1[5]
× D
= 1 × 1 = 1.
X
X.1
= (N
X.2
+ 2) × 1.
) can be realized.
X.1
AD9517-4
+ M
DCCOFF
0x19D[0]
0x19D[0]
0x1A2[0]
0x1A2[0]
X.1
+ 2) ×
1