LM4852LQBD National Semiconductor, LM4852LQBD Datasheet - Page 15

• Manufacturer Part Number: LM4852LQBD
• Description: BOARD EVALUATION LM4852LQ
• Manufacturer: National Semiconductor
• Series: Boomer®r

Specifications of LM4852LQBD

• Amplifier Type: Class AB
• Output Type: 1-Channel (Mono) with Stereo Headphones
• Max Output Power X Channels @ Load: 1.5W x 1 @ 4 Ohm; 60mW x 2 @ 32 Ohm
• Voltage - Supply: 2.6 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Board Type: Fully Populated
• Utilized Ic / Part: LM4852
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Application Information
TABLE 3. Volume Control
EXPOSED-DAP MOUNTING CONSIDERATIONS
The LM4852’s exposed-DAP (die attach paddle) package
(LD) provides a low thermal resistance between the die and
the PCB to which the part is mounted and soldered. This
allows rapid heat transfer from the die to the surrounding
PCB copper area heatsink, copper traces, ground plane, and
finally, surrounding air. The result is a low voltage audio
power amplifier that produces 1.1W dissipation in a 8Ω load
at ≤ 1% THD+N. This high power is achieved through careful
consideration of necessary thermal design. Failing to opti-
mize thermal design may compromise the LM4852’s high
power performance and activate unwanted, though neces-
sary, thermal shutdown protection.
The LD package must have its DAP soldered to a copper
pad on the PCB. The DAP’s PCB copper pad is then, ideally,
connected to a large plane of continuous unbroken copper.
This plane forms a thermal mass, heat sink, and radiation
area. Place the heat sink area on either outside plane in the
V4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
V3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
V2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
(Continued)
V1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
15
case of a two-sided or multi-layer PCB. (The heat sink area
can also be placed on an inner layer of a multi-layer board.
The thermal resistance, however, will be higher.) Connect
the DAP copper pad to the inner layer or backside copper
heat sink area with 6 (3 X 2) (LD) vias. The via diameter
should be 0.012in - 0.013in with a 1.27mm pitch. Ensure
efficient thermal conductivity by plugging and tenting the vias
with plating and solder mask, respectively.
Best thermal performance is achieved with the largest prac-
tical copper heat sink area. If the heatsink and amplifier
share the same PCB layer, a nominal 2.5in
necessary for 5V operation with a 4Ω load. Heatsink areas
not placed on the same PCB layer as the LM4852 should be
5in
The last two area recommendations apply for 25˚C ambient
temperature. Increase the area to compensate for ambient
temperatures above 25˚C. In all circumstances and under all
conditions, the junction temperature must be held below
2
(min) for the same supply voltage and load resistance.
V0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Gain (dB)
-40.5
-39.0
-37.5
-36.0
-34.5
-33.0
-31.5
-30.0
-28.5
-27.0
-25.5
-24.0
-22.5
-21.0
-19.5
-18.0
-16.5
-15.0
-13.5
-12.0
-10.5
-9.0
-7.5
-6.0
-4.5
-3.0
-1.5
0.0
1.5
3.0
4.5
6.0
G
2
(min) area is
www.national.com