QW1 TechTools, QW1 Datasheet - Page 209
Specifications of QW1
Contents
MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
For Use With/related Products
PIC Micro® MCU
For Use With
CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
QW152
Manufacturer:
Laird Technologies IAS
Quantity:
135
- Current page: 209 of 221
- Download datasheet (3Mb)
© 2007 TechTools
5.6
Power Supply Considerations
Your ClearView should now be ready to use.
power source before making the change.
modules, emulator, and/or target circuit.
Every Mathias Member Module provides a simple jumper which may be used to short the
power plane of both emulator and target together. This may be useful if you need to
power a small target circuit from the emulator, or if you want to power the emulator from
the target circuit. In either case, please note the following current limitations and
requirements: when powering a target circuit, the emulator cannot provide more than
approximately 50 mA; conversely, when powering the emulator from a target circuit, the
emulator needs approximately 500 mA.
If you need to change any of the plug-in modules, please be sure to disconnect any
Failure to disconnect power before replacing modules can result in damage to the
5)
6)
few seconds of internal testing, the LED should change to red; this indicates
that the unit is in emulation mode, but that execution is stopped.
7)
your PC. If your serial port has a DB-25 connector, you’ll need to use a DB-25
to DB-9 adapter.
8)
Plug the power supply into an AC outlet.
Plug the power supply cord into ClearView’s power jack.
The LED on ClearView should be green when power is applied. After a
Plug the female end of the serial cable into an available serial port on
Plug the male end of the serial cable into ClearView’s DB-9 connector.
ClearView Mathias Hardware
203
Related parts for QW1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ADAPT QUICKWRTR 4GANG 8/14SOIC N
Manufacturer:
TechTools
Datasheet:
Part Number:
Description:
ADAPT QUICKWRTR 4GANG 8/14SOIC W
Manufacturer:
TechTools
Datasheet:
Part Number:
Description:
ADAPTER QUICKWRITER 4GANG 18SOIC
Manufacturer:
TechTools
Datasheet:
Part Number:
Description:
ADAPTER QUICKWRITER 4GANG 44PLCC
Manufacturer:
TechTools
Datasheet:
Part Number:
Description:
ADAPTER QUICKWRITER 4GANG 28SOIC
Manufacturer:
TechTools
Datasheet: