QW1 TechTools, QW1 Datasheet - Page 21

• Manufacturer Part Number: QW1
• Description: PROGRAMMER PIC MCU QUICKWRITER
• Manufacturer: TechTools
• Series: QuickWriter™r
• Type: QuickWriterr

Specifications of QW1

• Contents: MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
• For Use With/related Products: PIC Micro® MCU
• For Use With: CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF

© 2007 TechTools
2.3
2.3.1
2.3.2
Shortcuts
Operation
Selecting the MCU
Overview
Details
Shortcuts
Setting the Configuration Word (Fuses)
Overview
Operation
5.
6.
7.
Alt+E, i (disable option editing for testing)
Alt+E, E (enable option editing for further editing)
Some HEX files will not contain the MCU type or you may want to select a different MCU to
program. When the MCU type changes, QuickWriter will adjust many aspects of the software to
match the capabilities of the selected device. Because of this it is very important to select the
proper MCU type (including prefixes such as 'A','B' and etc.).
Select "Options - Select MCU Type". When the MCU dialog opens use the cursor keys or the
mouse to select the desired MCU, then click the 'OK' button (or press the 'Enter' key) or "DBL-
Click" on the desired MCU.
(see also:
Alt+O, S
The configuration Word is set according to data stored in the HEX file when it is opened. However,
you are free to change this information in the program before programming the MCU, provided
"Option Editing" is enabled for this HEX file (see:
Options for Production Personnel
Specific bits in each Configuration Word control available MCU options when programmed.
After all settings have been verified, select "Disable Option Editing.." in the "Misc. Options"
section of the "General Options". You may also want to select "Disable Read Functions" in
this same location.
Select "File - Save Option Settings" from the main menu, then close the program.
Copy the HEX file and the corresponding control file (hexfilename.QWC) to the desired
location for production accessability. The production department can now open the HEX file
without fear of accidental changes.
·
·
·
·
·
Selecting the MCU
Setting the Configuration Word (Fuses)
Using Gang Adapters
Using Serial Numbers
Reading the MCU Contents
Setting HEX Options
15
17
17
9
14
)
19
).
15
Setting General Options
QuickWriter MCU Programmer
7
; see also:
Setting
15