QW1 TechTools, QW1 Datasheet - Page 23

• Manufacturer Part Number: QW1
• Description: PROGRAMMER PIC MCU QUICKWRITER
• Manufacturer: TechTools
• Series: QuickWriter™r
• Type: QuickWriterr

Specifications of QW1

• Contents: MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
• For Use With/related Products: PIC Micro® MCU
• For Use With: CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF

© 2007 TechTools
2.3.3
2.3.4
Shortcuts
Using Gang Adapters
Overview
Details
Shortcuts
Using Serial Numbers
Overview
During an "Auto Run" programming cycle, QuickWriter always verifies all sections of the MCU
before programming the Fuses. Programming the fuses last allows QuickWriter to perform a full
verification of all areas of the MCU regardless of the fuse settings.
Alt+E, W
When using Gang adapters, each device is programmed and verified independently, but at the
same time. Because of this, QuickWriter is able to save time while also tracking individual errors
that may occur for each device being programmed.
Gang adapters are available for all serially programmed devices that are supported by
QuickWriter. Multiple devices can be programmed at once without costing additional time except
for the minor delay while Serializing.
After connecting a gang adapter, you will want to enable multiple device support by selecting
multiple sockets in the QuickWriter software.
The Socket LED Indicators (shown above), will change states when "clicked" as shown below.
This can be done manually by toggling the button beneath each Socket LED Indicator or by using
the Main Menu: "Options - Programming Sockets - Gang" , which will select all 4 sockets.
Alt+O, P, G
QuickWriter programs serial numbers in Little Endian format. Any unused locations specified for
serial numbering will be set to '00'. Therefore, the HEX serial number "FFFE" programmed into 8
locations of EE Data will be stored as "FE FF 00 00 00 00 00 00". If auto increment is selected, the
next four incremented serial numbers will be stored as:
"FF FF 00 00 00 00 00 00"
"00 00 01 00 00 00 00 00"
"01 00 01 00 00 00 00 00"
"02 00 01 00 00 00 00 00"
Socket B disabled.
(FFFFh or 65535)
(10000h or 65536)
(10001h or 65537)
(10002h or 65538)
QuickWriter MCU Programmer
Socket A enabled
17