RELAY MINI 8A 12VDC PCB

DSP1A-L2-DC12V

Manufacturer Part NumberDSP1A-L2-DC12V
DescriptionRELAY MINI 8A 12VDC PCB
ManufacturerPanasonic Electric Works
SeriesDSP
TypePower Relay
DSP1A-L2-DC12V datasheets
 

Specifications of DSP1A-L2-DC12V

Relay TypeGeneral PurposeContact FormSPST-NO (1 Form A)
Contact Rating (current)8ASwitching Voltage250VAC
Coil TypeLatching, Dual CoilCoil Current25mA
Coil Voltage12VDCTurn On Voltage (max)9.6 VDC
Mounting TypeThrough HoleTermination StylePC Pin
CircuitSPST-NO (1 Form A)Contact Rating @ Voltage8A @ 250VAC
Control On Voltage (max)9.6 VDCRelay ConstructionLatching Double Coil
Contact ArrangementSPST-NOCoil Voltage Dc12V
Voltage Rating (vdc)30VVoltage Rating (vac)250V
Coil Resistance480OhmPick-up Voltage (max)9.6VDC
Maximum Power Rating150W/2KVAOperate Time10ms
Contact Current Rating5DC/8ACAContact MaterialSilver Tin Oxide/Gold Flash
Coil Suppression DiodeNoPush To Test ButtonNo
Led IndicatorNoSealSealed
Product Height (mm)10.5mmProduct Depth (mm)11mm
Product Length (mm)20.2mmOperating Temp Range-40C to 60C
Pin Count6Mounting StyleThrough Hole
Lead Free Status / RoHS StatusLead free / RoHS CompliantControl Off Voltage (min)-
Other names255-1618  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
Page 1/6

Download datasheet (131Kb)Embed
Next
DSP
DSP1a
DSP1
11.0
20.2
.433
.795
10.5
.413
DSP2a
mm
RoHS Directive compatibility information
http://www.nais-e.com/
SPECIFICATIONS
(at 20°C 68°F)
Contact
Arrangement
Contact material
Initial contact resistance, max.
(By voltage drop 6 V DC 1A)
8A 250
Nominal switching capacity
5A 30
2,000 VA
Max. switching power
150 W
Rating
Max. switching voltage
(resistive)
Max. switching current
Min. switching capacity
#1
Mechanical
Expected
(at 180 cpm)
life (min.
operations)
Electrical
Coil (polarized) (at 20°C 68°F)
Single side stable
Minimum operating
power
2 coil latching
Single side stable
Nominal operating
power
2 coil latching
Note: All specifications are based on the condition of 25°C 77°F, 50% R.H. unless
otherwise specified.
#1 This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the
actual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
*
1
Measurement at same location as “Initial breakdown voltage” section
*
Detection current: 10mA
2
*
3
Excluding contact bounce time
*
Half-wave pulse of sine wave: 11ms; detection time: 10µs
4
*
5
Half-wave pulse of sine wave: 6ms
*
Detection time: 10µs
6
*
7
Refer to 6. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT
8 A MINIATURE
POWER RELAY
IN DS RELAY SERIES
FEATURES
• Power types added to DS relay series
• High switching capacity:
1a: 8 A 250 V AC /
1a1b, 2a: 5 A 250 V AC
• High sensitivity: 190 mW pick-up
power
• High contact welding resistance
• Latching types available
• High breakdown voltage 3,000 Vrms
between contacts and coil 1,000
Vrms between open contacts
Meeting FCC Part 68
• Sealed types are standard
inch
Characteristics
1a
1a1b
2a
Max. operating speed
AgSnO
type
Initial insulation resistance*
2
30 mΩ
Initial
breakdown
voltage*
VAC
5A 250 VAC
5A 30 VDC
Surge voltage between contacts and
VDC
coil
1,250 VA
Set time*
150 W
Reset time*
250 V AC, 30 V DC
Operate time*
8 A
5 A
Release time(without diode)*
10 mA, 5 V DC
(at nominal voltage)
5×10
7
Temperature rise
10
5
Soldering temperature
192 mW
Shock
resistance
192 mW
300 mW
Vibration
300 mW
resistance
Conditions for operation, transport
and storage*
(Not freezing and condensing at low
temperature)
Unit weight
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
DSP RELAYS
About Cd-free contacts
We have introduced Cadmium free type
products to reduce Environmental
Hazardous Substances.
(The suffix “F” should be added to the
part number)
(Note: The Suffix “F” is required only for
1 Form A 1 Form B contact type.
The 1 Form A and 2 Form A contact type
is originally Cadmium free, the suffix “F”
is not required.)
Please replace parts containing
Cadmium with Cadmium-free products
and evaluate them with your actual
application before use because the life of
a relay depends on the contact material
and load.
30 cps. at rated load
Min. 1,000 MΩ at 500 V DC
1
Between open contacts
1,000 Vrms
Between contact sets
2,000 Vrms (1a1b, 2a)
Between contacts and
2
3,000 Vrms
coil
Min. 5,000 V
3
(at nominal voltage)
Max. 10 ms (Approx. 5 ms)
(at nominal voltage)
Max. 10 ms (Approx. 4 ms)
3
3
(at nominal voltage)
Max. 10 ms (Approx. 5 ms)
3
Max. 5 ms (Approx. 4 ms)
Max. 40°C (1a1b type)
Max. 55°C (1a, 2a types)
250°C (10 s) 300°C (5 s),
350°C (3 s)
Functional*
Min. 196 m/s
4
Destructive*
Min. 980 m/s
5
117.6 m/s
2
Functional*
6
at double amplitude of 2 mm
205.8 m/s
2
Destructive
at double amplitude of 3.5 mm
7
–40°C to +65°C
Approx. 4.3 g
{20 G}
2
{100 G}
2
{12 G}, 10 to 55 Hz
{21 G}, 10 to 55 Hz
– 40°F 149°F
.15 oz

DSP1A-L2-DC12V Summary of contents

  • Page 1

    ... DSP DSP1a DSP1 11.0 20.2 .433 .795 10.5 .413 DSP2a mm RoHS Directive compatibility information http://www.nais-e.com/ SPECIFICATIONS (at 20°C 68°F) Contact Arrangement Contact material Initial contact resistance, max. (By voltage drop 1A) 8A 250 Nominal switching capacity 5A 30 2,000 VA Max. switching power 150 W Rating Max ...

  • Page 2

    ... DSP❑-L2-DC9V (-F) 9 DSP❑-L2-DC12V (-F) 12 DSP❑-L2-DC24V (-F) 24 Notes: 1. Insert 1a in, 2 ❑ for contact form required. 2. The Suffix “F” is required only for DSP1-. DIMENSIONS 1a type (DSP1a) Single side stable 1 coil latching 20.2 .795 1.0 .039 0.8 .031 7 ...

  • Page 3

    DSP 1a1b type (DSP1) Single side stable 1 coil latching 20.2 .795 1.0 .039 0.8 .031 7.2 .283 10.16 7.62 .400 .300 2a type (DSP2a) Single side stable 1 coil latching 20.2 .795 1.0 .039 0.8 .031 7.2 .283 10.16 ...

  • Page 4

    ... Min. Max Min. Release time 100 120 Coil applied voltage, %V 5.-(1) Change of pick-up and drop-out voltage (1a type) Sample: DSP1a-DC12V, 5 pcs. Drop-out 50 voltage Pick-up voltage –40 – Ambient temperature, °C –50 All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. 3.-(2) Coil temperature rise (1a1b type) Sample: DSP1-DC12V, 5 pcs ...

  • Page 5

    ... DSP 6.-(1) Influence of adjacent mounting (1a type) Sample: DSP1a-DC12V, 5 pcs. 15 Pick-up voltage relays are not energized Drop-out voltage relays 10 are energized Inter-relay distance ( ), mm NOTES Soldering should be done under the following conditions: 250°C 482°F within 10 s 300°C 572°F within 5 s 350° ...

  • Page 6

    ... Remove the relay, applying force in the direction shown below case there is not enough space for finger to pick relay up, use screw drivers in the way shown below. For DSP1a For DSP1a, DSP1, DSP2a DSP1a-PS DSP1a-PSL2 DSP2a- ...