LBA120STR Clare, LBA120STR Datasheet
LBA120STR
Specifications of LBA120STR
LBA120STR
Related parts for LBA120STR
LBA120STR Summary of contents
Page 1
... CSA Certified Component: Certificate 1175739 • EN/IEC 60950-1 Certified Component TUV Certificate 49410 004 Ordering Information Part # LBA120 LBA120S LBA120STR LBA120P LBA120PTR Pin Configuration + Control - Normally Closed – Control - Normally Closed + Control - Normally Open – Control - Normally Open Switching Characteristics of ...
Page 2
... A 150 mW 800 mW 3750 V rms °C °C Conditions Symbol - 10ms I LPK I =170mA =250V LEAK =5mA, V =10V off V =50V, f=1MHz C L OUT I =120mA =5mA = I/O www.clare.com LBA120 Min Typ Max Units - - 170 400 Ω μ 0.4 0 0.9 1.2 1.4 V μ R06 ...
Page 3
... Turn-Off (ms) Form-A Typical I for Switch Dropout F (N=50, I =170mA , T =25º 0.1 0.3 0.5 0.7 0.9 1.1 LED Current (mA) www.clare.com vs. Temperature 100 120 Temperature (ºC) Form-A Typical On-Resistance Distribution (N=50, I =5mA, I =170mA , 0.23 8.45 8.75 9.05 9.35 9 ...
Page 4
... Load Voltage (V) Form-A Typical Leakage vs. Temperature Measured across Pins 5&6 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 100 -40 - Temperature (ºC) www.clare.com LBA120 Form-A Typical I for Switch Operation F vs. Temperature (I =170mA ) L DC 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 ...
Page 5
... LED Forward Current (mA) Form-B Typical Turn-On vs. Temperature (I =5mA, I =170mA ) 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 100 -40 - Temperature (ºC) www.clare.com Form-B Typical On-Resistance Distribution (N=50, I =5mA, I =170mA , 9.25 10.15 11.05 11.95 12.85 13.75 3.25 On-Resistance (Ω) Form-B Typical Blocking Voltage Distribution (N=50, T =25º ...
Page 6
... Load Voltage (V) Form-B Typical Leakage vs. Temperature Measured across Pins 7&8 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 -40 - 100 Temperature (ºC) www.clare.com LBA120 Form-B Typical Load Current vs. Temperature (I =5mA) F 250 200 150 100 50 0 -40 - 100 Temperature (ºC) ...
Page 7
... Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. ...
Page 8
... LBA120 PCB Hole Pattern 8-0.800 DIA. 2.540 ± 0.127 (8-0.031 DIA.) (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± ...
Page 9
... The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc ...