S216SE2 Sharp Microelectronics, S216SE2 Datasheet
S216SE2
Specifications of S216SE2
Available stocks
Related parts for S216SE2
S216SE2 Summary of contents
Page 1
... Reinforced Insulation Type Zero Cross type SIP 4pin Triac output SSR ■ Agency approvals/Compliance 1. Approved by TÜV EN60950 (reinforced insulation), file No. R9051479 (as models No. S216SE2) 2. Package resin : UL flammability grade (94V-0) ■ Applications (rms) ) iso 1. Isolated interface between high voltage AC devices and lower voltage DC control circuitry. ...
Page 2
... Epoxy resin S216SE2 Model No. Date code (2 digit) 16A260VAC + − ±0.2 4-1.1 ±0.3 4-1.25 ±0.2 4-0 (5.08) (7.62) (2.54) Product mass : approx. 6. Typical dimensions Output (Triac T2) 1 Output (Triac T1) 2 Input (+) 3 Input (−) 4 (Unit : mm) ±0.2 5.5 ±0.1 0.6 (1.4) 2 S216SE2 Series Sheet No.: D4-A03501EN ...
Page 3
... Country of origin Japan Rank mark There is no rank mark indicator and currently there are no rank offered for this device. 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D 3 S216SE2 Series Sheet No.: D4-A03501EN ...
Page 4
... V (rms)=200V, AC60Hz (rms)=2A, Resistance load, I off T R (j-c) Between junction and case th R (j-a) Between junction and ambient th 4 S216SE2 Series Soldering area (T a MIN. TYP. MAX. − 1.2 1.4 − − 100 − − 100 =20mA − − ...
Page 5
... EN60950 (reinforced insulation) − Model No. − Please contact a local SHARP sales representative to see the actual status of the production. Case V DRM 200pcs/case [V] Approved S216SE2F 600 Case V DRM 200pcs/case [V] Approved S216SE2 600 5 S216SE2 Series I [mA =6V =30Ω) L MAX.8 I [mA =6V =30Ω) L MAX.8 Sheet No.: D4-A03501EN ...
Page 6
... Ambient Temperature 75 100 125 (˚C) a Fig.4 Forward Current vs. Forward Voltage 100 75 100 125 (˚C) c Fig.6 Maximum ON-state Power Dissipation vs. RMS ON-state Current f=60Hz T =25˚C Start j 100 6 S216SE2 Series − 100 Ambient temperature T (˚ =75˚C a 50˚C 25˚C 0˚C −25˚C ...
Page 7
... Remarks : Please be aware that all data in the graph are just for reference. Fig.8 Repetitive Peak OFF-state Current vs. Ambient Temperature =30Ω 100 125 (˚ S216SE2 Series −3 V =600V D −4 −5 −6 −7 −8 −9 − 100 Ambient temperature T (˚C) a Sheet No.: D4-A03501EN 125 ...
Page 8
... OUT Locate snubber circuit between output terminals I (rms) OUT (Cs=0.1µF, Rs=47Ω) f − T − opr ) must be 0.1mA or less increases faster than rated dV/dt, the Triac may turn on. To avoid this situation S216SE2 Series MIN. MAX. Unit 0 240 V I (rms) T 0.1 mA ∗ ...
Page 9
... Please keep 5mm distance as minimum between naked metal portion of SSR and heat sink, and also between naked metal portion of SSR and bis/nut/washer. However, please avoid the natural rubber for isolation sheet. 4.4mm MIN. : 3kV or more) iso Heat sink SSR : each 3kV or more) iso Isolation sheet Heat sink SSR 9 S216SE2 Series Sheet No.: D4-A03501EN ...
Page 10
... Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least twice the minimum required triggering current from initial operation. ● Standard Circuit Tr1 ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. S216SE2 Load 3 1 SSR Line Surge absorption circuit (Snubber circuit S216SE2 Series Sheet No.: D4-A03501EN ...
Page 11
... Please solder within one time. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. 11 S216SE2 Series Sheet No.: D4-A03501EN ...
Page 12
... This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. 12 S216SE2 Series Sheet No.: D4-A03501EN ...
Page 13
... The product should be located after the packing case is partitioned and protected inside by 4 pads. Each partition should have 5 products with the lead upward. Cushioning material and molt plane should be located after all products are settled (1 packing contains 200 pcs). Package composition Molt plane Cushioning material Product Partition 13 S216SE2 Series Pad Packing case Sheet No.: D4-A03501EN ...
Page 14
... SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this pub- lication. 14 S216SE2 Series Sheet No.: D4-A03501EN ...