RES ARRAY 2.2K OHM 8TRM 4RES SMD

TC164-JR-072K2L

Manufacturer Part NumberTC164-JR-072K2L
DescriptionRES ARRAY 2.2K OHM 8TRM 4RES SMD
ManufacturerYageo
SeriesTC164
TC164-JR-072K2L datasheet
 


Specifications of TC164-JR-072K2L

Temperature Coefficient±200ppm/°CResistance (ohms)2.2K
Number Of Resistors4Circuit TypeIsolated
Tolerance±5%Power Per Element62.5mW
Number Of Pins8Package / Case1206 (3216 Metric), Concave
Size / Dimension0.126" L x 0.063" W (3.20mm x 1.60mm)Height0.024" (0.60mm)
Mounting TypeSurface MountOperating Temperature-55°C ~ 155°C
Resistance2.2kohmResistance Tolerance± 5%
Power Rating63mWVoltage Rating50V
No. Of Elements4Resistor Case Style1206
SvhcNo SVHCLead Free Status / RoHS StatusLead free / RoHS Compliant
Other namesTC164J-2.2KTR  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
Page 6/8

Download datasheet (331Kb)Embed
PrevNext
Chip Resistor Surface Mount
TESTS AND REQUIREMENTS
Table 4 Test condition, procedure and requirements
TEST
TEST METHOD
MIL-STD-202G-method 108A
Life/
Operational Life/
IEC 60115-1 4.25.1
Endurance
JIS C 5202-7.10
MIL-STD-202G-method 108A
High
Temperature
IEC 60115-1 4.25.3
Exposure/
JIS C 5202-7.11
Endurance at
upper category
temperature
MIL-STD-202G-method 106F
Moisture
IEC 60115-1 4.24.2
Resistance
MIL-STD-202G-method 107G
Thermal Shock
MIL-R-55342D-para 4.7.5
Short time
overload
IEC60115-1 4.13
IEC60115-1 4.33
Board Flex/
Bending
Oct 27, 2008 V.3
YC/TC
164 (RoHS Compliant)
SERIES
PROCEDURE
1,000 hours at 70±5 °C applied RCWV
1.5 hours on, 0.5 hour off, still air required
1,000 hours at maximum operating temperature
depending on specification, unpowered
No direct impingement of forced air to the parts
Tolerances: 155±3 °C
Each temperature / humidity cycle is defined at 8
hours (method 106F), 3 cycles / 24 hours for 10d
with 25 °C / 65 °C 95% R.H, without steps 7a &
7b, unpowered
Parts mounted on test-boards, without
condensation on parts
Measurement at 24±2 hours after
test conclusion
-55/+155 °C
Note: Number of cycles required is 300. Devices
unmounted
Maximum transfer time is 20 seconds. Dwell time
is 15 minutes. Air – Air
2.5 times RCWV or maximum overload voltage
whichever is less for 5 sec at room temperature
Device mounted on PCB test board as described,
only 1 board bending required
3 mm bending
Bending time: 60±5 seconds
Ohmic value checked during bending
6
Product specification
8
REQUIREMENTS
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(1%+0.05 Ω)
<50 mΩ for Jumper
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(0.5%+0.05 Ω) for 10 KΩ to
10 MΩ
±(1%+0.05 Ω) for others
<50 mΩ for Jumper
±(2%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
±(1%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
www.yageo.com