CAPACITOR TANT 33UF 16V 20% SMD

T491D336M016AT

Manufacturer Part NumberT491D336M016AT
DescriptionCAPACITOR TANT 33UF 16V 20% SMD
ManufacturerKemet
SeriesT491
TypeMolded
T491D336M016AT datasheet
 


Specifications of T491D336M016AT

Capacitance33µFVoltage - Rated16V
Tolerance±20%Esr (equivalent Series Resistance)800.0 mOhm
Operating Temperature-55°C ~ 125°CMounting TypeSurface Mount
Package / Case2917 (7343 Metric)Size / Dimension0.287" L x 0.169" W (7.30mm x 4.30mm)
Height0.110" (2.80mm)Manufacturer Size CodeD
FeaturesGeneral PurposeVoltage Rating16 Volts
Esr0.8 OhmsOperating Temperature Range- 55 C to + 125 C
Mfr Case CodeD CaseDimensions4.3 mm W x 7.3 mm L x 2.8 mm H
Leakage Current5.3 uAmpsProductTantalum Solid Standard Grade - Other Various
Termination StyleSMD/SMTLead Free Status / RoHS StatusLead free / RoHS Compliant
Lead Spacing-Other names399-3789-2
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
Page 19/24

Download datasheet (3Mb)Embed
PrevNext
Standard MnO
Tantalum Surface Mount Capacitors – T491 Industrial Grade MnO
2
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
T
2
ØDo
Ko
B
1
S
1
T
1
Center Lines of Cavity
Cover Tape
B
is for tape feeder reference only,
1
including draft concentric about B
.
User Direction of Unreeling
o
Table 5 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
D
Tape Size
D
1
Note 1
0
1.0
8mm
(0.039)
1.5 +0.10/-0.0
12mm
(0.059 +0.004/-0.0)
1.5
(0.059)
16mm
B
Max.
Tape Size
Pitch
1
Note 4
4.35
8mm
Single (4mm)
(0.171)
Single (4mm) &
8.2
12mm
Double (8mm)
(0.323)
12.1
16mm
Triple (12mm)
(0.476)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S
<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
1
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defi ned by A
, B
and K
shall surround the component with suffi cient clearance that:
0
0
0
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) for KPS Series product A
and B
are measured on a plane 0.3mm above the bottom of the pocket.
0
0
(f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Series
2
P
2
[10 pitches cumulative
Po
tolerance on tape ±0.2 mm]
Ao
F
E
2
Bo
P
1
Embossment
ØD
1
For cavity size,
see Note 1 Table 5
Constant Dimensions — Millimeters (Inches)
Min.
E
P
1
0
1.75 ± 0.10
4.0 ± 0.10
(0.069 ± 0.004)
(0.157 ± 0.004)
Variable Dimensions — Millimeters (Inches)
E
Min.
F
2
6.25
3.5 ± 0.05
(0.246)
(0.138 ± 0.002)
10.25
5.5 ± 0.05
(0.404)
(0.217 ± 0.002)
14.25
5.5 ± 0.05
(0.561)
(0.217 ± 0.002)
E
1
W
R Ref.
S
P
1
Note 2
Note 3
2
25.0
(0.984)
2.0 ± 0.05
0.600
(0.079 ± 0.002)
(0.024)
30
(1.181)
P
T
Max
W Max
1
2
4.0 ± 0.10
2.5
8.3
(0.157 ± 0.004)
(0.098)
(0.327)
8.0 ± 0.10
4.6
12.3
(0.315 ± 0.004)
(0.181)
(0.484)
8.0 ± 0.10
4.6
16.3
(0.315 ± 0.004)
(0.181)
(0.642)
T2005-1 • 1/17/2011
Min.
T Max.
T
Max.
1
0.600
0.100
(0.024)
(0.004)
A
,B
& K
0
0
0
Note 5
19 19