CAP POLY ALUM 1000UF 6.3V SMD

PCG0J102MCL1GS

Manufacturer Part NumberPCG0J102MCL1GS
DescriptionCAP POLY ALUM 1000UF 6.3V SMD
ManufacturerNichicon
SeriesCG
PCG0J102MCL1GS datasheet
 


Specifications of PCG0J102MCL1GS

Capacitance1000µFVoltage Rating6.3V
Tolerance±20%Lifetime @ Temp.2000 Hrs @ 105°C
Operating Temperature-55°C ~ 105°CFeaturesPolymer
Ripple Current3.8AEsr (equivalent Series Resistance)18.0 mOhm
Mounting TypeSurface MountPackage / CaseRadial, Can - SMD
Size / Dimension0.394" Dia (10.00mm)Height0.315" (8.00mm)
Surface Mount Land Size0.406" L x 0.406" W (10.30mm x 10.30mm)Esr18 mOhms
Operating Temperature Range- 55 C to + 105 CTermination StyleSMD/SMT
Dimensions10 mm Dia x 8 mm LDissipation Factor Df0.12
Leakage Current1260 uAmpsLoad Life2000 Hrs
ProductOrganic Polymer Aluminum - Chip CapacitorsLead Free Status / RoHS StatusLead free / RoHS Compliant
Lead Spacing-Other names493-3086-2
1
Page 1
2
Page 2
Page 1/2

Download datasheet (48Kb)Embed
Next
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CG
Chip Type, Higher Capacitance
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
– 55 to +105°C
Category Temperature Range
Rated Voltage Range
2.5 to 16V
47 to 3300µF
Rated Capacitance Range
Capacitance Tolerance
± 20% at 120Hz, 20°C
Less than or equal to the specified value at 120Hz, 20°C
Tangent of loss angle (tan )
Less than or equal to the specified value at 100kHz, 20°C
ESR (
1)
Less than or equal to the specified value.
Leakage Current (
2)
Temperature Characteristics
Z+105°C / Z+20°C
Z – 55°C / Z+20°C
(Max.Impedance Ratio)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
Endurance
applied for 2000 hours at 105°C.
The specifications listed at right shall be met when the
Damp Heat
capacitors are restored to 20°C after the rated voltage is
(Steady State)
applied for 1000 hours at 60°C, 90% RH.
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
Resistance to
not exceed 60 seconds.
Soldering Heat
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Plastic platform
Capacitance
Lot No.
0.3 MAX.
+0.1
L
Voltage ( j:6.3v)
Series
- 0.4
Size
5
6L
6.3
6L
8
7L
10
8L
10
D
5.0
6.3
8.0
10.0
L
5.9
5.9
6.9
7.9
A
6.0
7.3
9.0
11.0
B
5.3
6.6
8.3
10.3
C
5.3
6.6
8.3
10.3
E
1.6
2.1
3.2
4.6
H
0.5 to 0.8
0.5 to 0.8
0.8 to 1.1
0.8 to 1.1
0.8 to 1.1
Dimension table in next page.
CG
Higher
Capacitance
CF
Performance Characteristics
After 2 minutes' application of rated voltage at 20°C
1.25
(100kHz)
1.25
Capacitance change
tan
(
ESR
Leakage current (
Capacitance change
tan
(
ESR
Leakage current (
Capacitance change
tan
(
ESR
Leakage current (
Type numbering system (Example : 6.3V 470µF)
Positive
1
2
3
P
C
G
C 0.2
Negative
H
(mm)
10L
10 12.7L
10.0
10.0
9.9
12.6
11.0
11.0
Voltage
10.3
10.3
10.3
10.3
V
4.6
4.6
Code
0.8 to 1.1
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
1)
150% or less than the initial specified value
2)
Less than or equal to the initial specified value
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
1)
150% or less than the initial specified value
2)
Less than or equal to the initial specified value
Within ± 10% of the initial capacitance value (
130% or less than the initial specified value
1)
130% or less than the initial specified value
2)
Less than or equal to the initial specified value
4
5
6
7
8
9
10
11
12
13
14
0
J
4
7
1
M
C
L
1
G
S
Capacitance toleranc ( 20%)
Rated capacitance (470 F)
Rated voltage (6.3V)
2.5
4
6.3
10
16
e
g
j
A
C
CAT.8100Z
3)
3)
3)
Taping code
Configuration
Series name
Type

PCG0J102MCL1GS Summary of contents

  • Page 1

    ... CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CG Chip Type, Higher Capacitance series Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). Specifications Item – ...

  • Page 2

    ... PCG0G181MCL1GS 22 2700 PCG0G391MCL1GS 21 3200 PCG0G681MCL1GS 17 4000 PCG0G122MCL1GS 13 4600 PCG0G222MCL1GS 11 5300 PCG0G272MCL1GS 33 1800 PCG0J151MCL1GS 23 2600 PCG0J271MCL1GS 23 2700 PCG0J331MCL1GS 22 3100 PCG0J471MCL1GS 18 3800 PCG0J102MCL1GS 14 4400 PCG0J182MCL1GS 12 5000 PCG0J222MCL1GS 35 1700 PCG1A820MCL1GS 25 2500 PCG1A151MCL1GS 23 3100 PCG1A331MCL1GS 20 3600 PCG1A561MCL1GS 15 4300 PCG1A821MCL1GS 13 4800 PCG1A102MCL1GS 40 1500 PCG1C470MCL1GS 30 2300 PCG1C820MCL1GS ...