11c90 National Semiconductor Corporation, 11c90 Datasheet

no-image

11c90

Manufacturer Part Number
11c90
Description
650 Mhz Prescalers
Manufacturer
National Semiconductor Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
11c90DC
Manufacturer:
NSC
Quantity:
900
Part Number:
11c90DC
Manufacturer:
NSC
Quantity:
900
Part Number:
11c90DC
Manufacturer:
MIT
Quantity:
5 704
Part Number:
11c90DC
Manufacturer:
UTMC
Quantity:
21
Part Number:
11c90DC
Manufacturer:
F
Quantity:
20 000
Part Number:
11c90DMQB
Manufacturer:
TI
Quantity:
1 044
C 1995 National Semiconductor Corporation
11C90 11C91
650 MHz Prescalers
General Description
The 11C90 and 11C91 are high-speed prescalers designed
specifically for communication and instrumentation applica-
tions All discussions and examples in this data sheet are
applicable to the 11C91 as well as the 11C90
The 11C90 will divide by 10 or 11 and the 11C91 by 5 or 6
both over a frequency range from DC to typically 650 MHz
The division ratio is controlled by the Mode Control The
divide-by-10 or -11 capability allows the use of pulse swal-
lowing techniques to control high-speed counting modulos
by lower-speed circuits The 11C90 may be used with either
ECL or TTL power supplies
In addition to the ECL outputs Q and Q the 11C90 contains
an ECL-to-TTL converter and a TTL output The TTL output
operates from the same V
but a separate pin is used for the TTL circuit V
mizes noise coupling when the TTL output switches and
Logic Symbol
CE
CP
M
MS
Q Q
QTTL
RM
V
Pin Names
REF
n
n
Count Enable Input (Active LOW)
Clock Pulse Input
Count Modulus Control Input
Asynchronous Master Set Input
ECL Outputs
TTL Output
2 kX Resistor to M
400X Resistor to V
CC
and V
TL F 9892
Description
EE
levels as the counter
n
BB
EE
TL F 9892 – 2
This mini-
also allows power consumption to be reduced by leaving
the separate V
To facilitate capacitive coupling of the clock signal a 400X
resistor (V
Connecting this resistor to the Clock Pulse input (CP) auto-
matically centers the input about the switching threshold
Maximum frequency operation is achieved with a 50% duty
cycle
Each of the Mode Control inputs is connected to an internal
2 kX resistor with the other end uncommitted (RM
RM
from the same V
ciated 2 kX resistor to V
from the ECL circuit the 2 kX resistor can be left open or if
required can be connected to V
resistor
Connection Diagram
2
) An M input can be driven from a TTL circuit operating
REF
Not Intended For New Designs
) is connected internally to the V
EE
CC
pin open if the TTL output is not used
by connecting the free end of the asso-
16-Pin DIP
CCA
When an M input is driven
EE
to act as a pull-down
RRD-B30M115 Printed in U S A
BB
August 1992
reference
TL F 9892 – 1
1
and

Related parts for 11c90

11c90 Summary of contents

Page 1

... All discussions and examples in this data sheet are applicable to the 11C91 as well as the 11C90 The 11C90 will divide and the 11C91 both over a frequency range from DC to typically 650 MHz The division ratio is controlled by the Mode Control The ...

Page 2

Absolute Maximum Ratings Above which the useful life may be impaired If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications b Storage Temperature Maximum Junction Temperature (T ...

Page 3

ECL Operation Commercial Version DC Electrical Characteristics GND CCA EE Symbol Parameter Min b V Output HIGH Voltage 1060 and Q 1025 b 980 V Output LOW ...

Page 4

ECL Operation Military Version DC Electrical Characteristics GND CCA EE Symbol Parameter Min b V Output HIGH Voltage 1100 and Q 980 b 910 V Output LOW ...

Page 5

Conditions 50X (scope input impedance Jig and stray capacitance equal 50X impedance lines 1 ...

Page 6

... This gives an allowable delay of ten clock periods minus the delay of the 11C90 and the setup time If the external logic uses the negative output transition as its active edge the allowable delay is reduced to five clock ...

Page 7

... Note A HIGH on MS forces all Qs HIGH be connected together as close to the package as possible Pin 12 must always be connected to the V supply while pin 13 is required only if the TTL output is used Low impedance V CC pass capacitors are recommended to prevent crosstalk Operating Mode Table 11C90 Inputs ...

Page 8

... HIGH Voltage Level e L LOW Voltage Level TL F 9892 – Don’t Care 11C90 Special Variations e QR Commercial grade device with burn-in Temperature Range e C Commercial ( 9892 – 8 Output Response M ...

Page 9

9 ...

Page 10

Physical Dimensions inches (millimeters) 16 Lead Ceramic Dual-In-Line Package (D) LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR ...

Related keywords