74hct6323a NXP Semiconductors, 74hct6323a Datasheet
74hct6323a
Available stocks
Related parts for 74hct6323a
74hct6323a Summary of contents
Page 1
DATA SHEET For a complete data sheet, please also download: The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications The IC06 74HC/HCT/HCU/HCMOS Logic Package Information The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines 74HC/HCT6323A Programmable ripple counter with oscillator; 3-state Product specification Supersedes data of ...
Page 2
Philips Semiconductors Programmable ripple counter with oscillator; 3-state FEATURES 8-pin space saving package Programmable 3-stage ripple counter Suitable for over-tone crystal application MHz ( 10%) CC 3-state output buffer Two internal capacitors Recommended operating ...
Page 3
Philips Semiconductors Programmable ripple counter with oscillator; 3-state PINNING SYMBOL PIN DESCRIPTION OUT 1 counter output mode select inputs for divide GND 4 ground ( master ...
Page 4
Philips Semiconductors Programmable ripple counter with oscillator; 3-state X2 handbook, full pagewidth ( Internal capacitors typical 7 pF each. Including stray capacitors on pin X1 and X2, total capacitance will be typical 12 pF per ...
Page 5
Philips Semiconductors Programmable ripple counter with oscillator; 3-state DC CHARACTERISTICS FOR 74HC For the DC characteristics see “74HC/HCT/HCU/HCMOS Logic Family Specifications” Output capability: non-standard; bus driver (except for X2) I category: MSI. CC Voltages are referenced to GND (ground = ...
Page 6
Philips Semiconductors Programmable ripple counter with oscillator; 3-state SYMBOL PARAMETER MIN V LOW level OL output voltage OUT I input leakage LI current X1 I input pull- current S1, S2 and MR I quiescent CC supply current September ...
Page 7
Philips Semiconductors Programmable ripple counter with oscillator; 3-state AC CHARACTERISTICS FOR 74HC GND = ns pF SYMBOL PARAMETER MIN t /t propagation PHL PLH delay X1 to ...
Page 8
Philips Semiconductors Programmable ripple counter with oscillator; 3-state DC CHARACTERISTICS FOR 74HCT For the DC characteristics see “74HC/HCT/HCU/HCMOS Logic Family Specifications” Output capability: bus driver (except for X2). I category: MSI. CC Voltages are referenced to GND (ground = 0 ...
Page 9
Philips Semiconductors Programmable ripple counter with oscillator; 3-state SYMBOL PARAMETER MIN V LOW level OL output voltage X2 output V LOW level OL output voltage OUT V LOW level OL output voltage OUT I input leakage LI current I input ...
Page 10
Philips Semiconductors Programmable ripple counter with oscillator; 3-state AC CHARACTERISTICS FOR 74HCT GND = ns SYMBOL PARAMETER MIN t /t propagation PHL PLH delay X1 to ...
Page 11
Philips Semiconductors Programmable ripple counter with oscillator; 3-state R = 560 k bias handbook, halfpage V CC 0.47 F output 100 F input kHz) Fig.5 Test set-up for measuring forward transconductance ...
Page 12
Philips Semiconductors Programmable ripple counter with oscillator; 3-state handbook, full pagewidth MR INPUT OUTPUT LOW - to - OFF OFF - to - LOW OUTPUT HIGH - to - OFF OFF - to - HIGH MBA319 ( ...
Page 13
Philips Semiconductors Programmable ripple counter with oscillator; 3-state APPLICATION INFORMATION handbook, halfpage 6323A 5 MR MBA348 The input pull-up current is used to create a power-on delay time at MR. Fig.10 Power-on reset. 50 handbook, halfpage ...
Page 14
Philips Semiconductors Programmable ripple counter with oscillator; 3-state handbook, halfpage MR (from logic bias 100 MBA328 - 1 Above 5 MHz replace capacitor of ...
Page 15
Philips Semiconductors Programmable ripple counter with oscillator; 3-state Typical Crystal Oscillator In Fig.13 the power limiting resistor. For starting and maintaining oscillation a minimum transconductance is necessary should not be too large. A practical value for ...