ADG453 AD [Analog Devices], ADG453 Datasheet
ADG453
Available stocks
Related parts for ADG453
ADG453 Summary of contents
Page 1
... The ADG451 switches are turned on with a logic low on the appropriate control input, while a logic high is required for the ADG452. The ADG453 has two switches with digital con- trol logic similar to that of the ADG451 while the logic is in- verted on the other two switches. ...
Page 2
... DIGITAL INPUTS Input High Voltage, V INH Input Low Voltage, V INL Input Current INL INH 3 DYNAMIC CHARACTERISTICS OFF Break-Before-Make Time Delay (ADG453 Only) Charge Injection OFF Isolation Channel-to-Channel Crosstalk C (OFF (OFF (ON POWER REQUIREMENTS I DD ...
Page 3
... D S DIGITAL INPUTS Input High Voltage, V INH Input Low Voltage, V INL Input Current INL INH 4 DYNAMIC CHARACTERISTICS OFF Break-Before-Make Time Delay (ADG453 Only) Charge Injection Channel-to-Channel Crosstalk C (OFF (OFF (ON POWER REQUIREMENTS ...
Page 4
... DIGITAL INPUTS Input High Voltage, V INH Input Low Voltage, V INL Input Current INL INH 4 DYNAMIC CHARACTERISTICS OFF Break-Before-Make Time Delay (ADG453 Only) Charge Injection OFF Isolation Channel-to-Channel Crosstalk C (OFF (OFF (ON POWER REQUIREMENTS I DD ...
Page 5
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADG451/ADG452/ADG453 feature proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 6
... ADG451/ADG452/ADG453 V Most positive power supply potential Most negative power supply potential in dual SS supplies. In single supply applications, it may be connected to GND. V Logic power supply (+5 V). L GND Ground (0 V) reference. S Source terminal. May be an input or output. D Drain terminal. May be an input or output. IN Logic control input. ...
Page 7
... D S for Different Temperatures with Single Supplies –0.1 –0.2 –0.3 –0.4 –0 Figure 7. Leakage Currents as a Function 4SW 1SW 10 100k 1M 10M –7– ADG451/ADG452/ADG453 V = +15V + ...
Page 8
... L Due to switch and capacitor leakage, the voltage on the hold capacitor will decrease with time. The ADG451/ ADG452/ADG453 minimizes this droop due to its low leakage specifications. The droop rate is further minimized by the use of a polystyrene hold capacitor. The droop rate for the circuit shown is typically ...
Page 9
... V SS –15V Test Circuit 4. Switching Times 0 OUT1 35pF 300 V OUT2 35pF 300 Test Circuit 5. Break-Before-Make Time Delay –9– ADG451/ADG452/ADG453 I (ON Test Circuit 3. On Leakage 3V ADG451 50% 50% 3V 50% 50% ADG452 90% 90 OFF 3V V 50% ...
Page 10
... ADG451/ADG452/ADG453 OUT +15V + OUT C L 10nF V GND DD –15V Test Circuit 6. Charge Injection +5V +15V 0 GND 0.1 F –15V Test Circuit 7. Off Isolation +15V +5V 0 IN1 ...
Page 11
... SOIC (R-16A) 0.3937 (10.00) 0.3859 (9.80 0.1574 (4.00) 0.2440 (6.20 0.1497 (3.80) 0.2284 (5.80) 0.0688 (1.75) PIN 1 0.0098 (0.25) 0.0532 (1.35) 0.0040 (0.10) 0.0500 0.0192 (0.49) SEATING 0.0099 (0.25) (1.27) 0.0138 (0.35) PLANE BSC 0.0075 (0.19) –11– ADG451/ADG452/ADG453 0.325 (8.26) 0.195 (4.95) 0.300 (7.62) 0.115 (2.93) 0.015 (0.381) 0.008 (0.204) 0.0196 (0.50 0.0099 (0.25 0.0500 (1.27) 0.0160 (0.41) ...
Page 12
–12– ...