CAT524 Catalyst Semiconductor, CAT524 Datasheet
CAT524
Available stocks
Related parts for CAT524
CAT524 Summary of contents
Page 1
... NVRAM memory Erase/Write cycle. The CAT524 is available in the commercial and – industrial operating temperature ranges. Both 14-pin plastic DIP and SOIC packages are offered. ...
Page 2
... CAT524 ABSOLUTE MAXIMUM RATINGS* Supply Voltage V to GND ...................................... –0.5V to +7V DD Inputs CLK to GND ............................ –0. GND .............................. –0. GND ............................... –0. PROG to GND ........................ –0. GND ........................ –0. REF GND ......................... –0. REF Outputs D to GND ............................... –0. ...
Page 3
... L see note pF +5V LOAD pF +3V LOAD MHz MHz OUT / CAT524 Min Typ Max Units 0.99 V 0.995 V — — 0.005 V 0. — — 1 — — 100 k — — ...
Page 4
... CAT524 A. C. TIMING DIAGRAM Doc. No. 25076-00 Rev. 4/01 M-1 4 ...
Page 5
... CLOCK The CAT524’s clock controls both data flow in and out of the IC and EEPROM memory cell programming. Serial data is shifted into the DI pin and out of the DO pin on the clock’s rising edge. While it is not necessary for the clock ...
Page 6
... DATA OUTPUT Data is output serially by the CAT524, LSB first, via the Data Out (DO) pin following the reception of a start bit and two address bits by the Data Input (DI). becomes active whenever CS goes high and resumes its high impedance Tri-State mode when CS returns low ...
Page 7
... EEPROM then a change would occur at the read cycle’s conclusion. TEMPORARILY CHANGE OUTPUT The CAT524 allows temporary changes in DAC’s output to be made without disturbing the settings retained in EEPROM memory. This feature is particularly useful when testing for a new output setting and allows for user adjustment of preset or default values without losing the original factory settings ...
Page 8
... R = ——————————— DPP V L REF + OFFSET + -V REF – -V for Dual Power Supply Systems 15K 10 F 1N5231B 5. REF CAT524 + CAT514 – LM 324 GND V L REF 4.02 K 1.00K Digitally Controlled Voltage Reference + ) - (V ) REF OFFSET OFFSET 1 A ...
Page 9
... WINDOW 2 + – + – 10K +5V WINDOW 3 + – + – 10K +5V WINDOW 4 + – + – 10K +5V WINDOW 5 + – Overlapping Window Comparator 9 CAT524 REF WINDOW 1 1 WINDOW 2 2 WINDOW 3 3 WINDOW 4 4 WINDOW 5 WINDOW STRUCTURE V REF WINDOW OUT WINDOW OUT WINDOW OUT WINDOW 4 ...
Page 10
... CONTROL & DATA +5V CONTROL CAT524 & DATA GND Doc. No. 25076-00 Rev. 4/01 M-1 +5V 2. REF H 4.7 A LM385-2.5 +15V DPP + +5V – 10K 10K CAT524 DPP + – 5M GND REF 10K Current Sink with 4 Decades of Resolution 51K + – 10K REF 5M 5M DPP – ...
Page 11
... Digital Stereo Control 0. TREB CAP BASS CAP 0. OUTPUT 1 Z LM1040 LOUDNESS VOLUME BALANCE BYPASS TREBLE BASS 15 OUTPUT 2 0. BASS CAP 21 TREB CAP STEREO 24 0.01 F GND ENHANCE 12 GND Doc. No. 25076-00 Rev. 4/01 CAT524 +12V 0.1 F OUT 1 OUT 2 ...
Page 12
... ORDERING INFORMATION Prefix Device # CAT 524 Optional Product Company ID Number Notes: (1) The device used in the above example is a CAT524JI-TE13 (SOIC, Industrial Temperature, Tape & Reel) Doc. No. 25076-00 Rev. 4/01 M-1 Suffix J I Package P: PDIP J: SOIC Temperature Range Blank = Commercial (0˚C to +70˚ Industrial (-40˚C to +85˚C) ...