ch1840 ETC-unknow, ch1840 Datasheet

no-image

ch1840

Manufacturer Part Number
ch1840
Description
Profile Data Access Arrangement Modules
Manufacturer
ETC-unknow
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ch1840D
Manufacturer:
HRS
Quantity:
1 338
INTRODUCTION
The CH1840 is an ultra small, low profile Data Access Arrange-
ment (DAA). Its modular construction and single +5 Volt D.C. power
requirement simplify your development process. Specifically de-
signed for both voice and data, this device allows direct connec-
tion of these circuits to the telephone lines. The CH1840 has FCC
Part 68 registration that can be transferred to your product. Simply
attach the included registration sticker to the outside of your prod-
uct. This eliminates the costs and delays associated with Part 68
testing and registration.
The CH1840 has also been designed to meet the requirements of
Canada’s Department of Communication (DOC). However, it is
necessary to register your product with the DOC before use in
Canada.
The CH1840 requires only 1.5 square inches of circuit board space
and presents a profile of only 0.35 inches in height. This DAA can
either be mounted directly on a printed circuit board or socketed.
Connection is made through 0.025 inch square pins on 0.10 inch
centers. The telephone line connection is made through a user
supplied RJ-11 jack.
The CH1840 DAA is designed for use with a variety of voice circuitry
and LSI modem/fax chip sets. This device is ideal for fax and
modem applications up through V.32bis. The CH1840 is pin com-
patible with the CH1817.
© 2000 Cermetek Microelectronics, Inc.
C
Figure 1. CH1840 Functional Block Diagram
ermetek
microelectronics
Low Profile Data Access Arrangement (DAA) Modules
Page 1
CH1840
FEATURES
FUNCTIONAL DESCRIPTION
The operation of the CH1840 can be broken down into the
functional blocks shown in Figure 1.
Control inputs and status outputs for the CH1840 are compat-
ible with 5 Volt CMOS. See the Electrical Specifications.
Phone Line Control
In the Public Switched Telephone Network (PSTN), the wires
from a telephone to the phone company’s central office (CO) are
referred to as the local loop.
1) Phone line control
2) Billing delay
3) Ring detection
4) Signal Path
5) 2- to 4-wire converter
Works with all modem chip sets
Available in 0 dB, -6 dB, and -9 dB insertion losses
Available in extended temperature operation,
-40
Complete DAA function
Voice and data
FCC Part 68 registered
Registration conveyed to user
Hook switch control
Ring detection
Single +5V operation
Pulse dial capability
o
C to +85
o
C
Document No. 607-0011 Rev. A (5/00)

Related parts for ch1840

ch1840 Summary of contents

Page 1

... Connection is made through 0.025 inch square pins on 0.10 inch centers. The telephone line connection is made through a user supplied RJ-11 jack. The CH1840 DAA is designed for use with a variety of voice circuitry and LSI modem/fax chip sets. This device is ideal for fax and modem applications up through V.32bis. The CH1840 is pin com- patible with the CH1817 ...

Page 2

... Drawing current from the local loop signals the central office that the telephone is Off Hook, that is, either answering a call or prepar- ing to place a call. In the CH1840, this function is controlled by the OFFHK signal. When this input is LOW, the CH1840 is On-Hook, indicating to the central office it is not using the line. The CH1840 can pulse dial by toggling the OFFHK input ...

Page 3

... N/C - Not Used. Please leave unconnected. OFF HOOK, Input. When set Low, the CH1840 is placed on-Hook. When set HICH, the CH1840 is placed Off-Hook to answer or place a call. This input can also be used for pulse dialing. NOTE: When answering incoming calls in response to 4 OFFHK ...

Page 4

... No additional application circuitry should be connected be- tween the CH1840 and the phone line RJ-11C jack, except as described in note 10 below. 8) The registration label included with the product must be affixed to the outside of your product where it is easily visible to your end user ...

Page 5

... Many socket manufac- turers offer socket strips that accept the 0.025 inch square pins on 0.10 inch centers. When using mechanical sockets, restraint of the CH1840 should be provided to keep it seated during ship- ment. Plastic cablewraps are secure yet easily removed. FOR YOUR USER’S MANUAL ...

Page 6

... Z FCC Registration Number Ringer Equivalence REN TIMERS Ring Detection Delay T Billing Delay Timer T Hook Switch Power Supply Current I © 2000 Cermetek Microelectronics, Inc. Table 2 CH1840 DAA Electrical Specifications T = 0ºC to 55ºC unless otherwise specified A CONDITIONS 0.2mA ...

Page 7

TASMAN DRIVE · SUNNYVALE, CALIFORNIA 94089 · TEL: (408) 752-5000 FAX: (408) 752-5004 Cermetek reserves the right to make changes in specifications at any time and without notice. The information furnished by Cermetek in this publication is believed to ...

Related keywords