EL7563C Elantec Semiconductor, EL7563C Datasheet
EL7563C
Available stocks
Related parts for EL7563C
EL7563C Summary of contents
Page 1
... The minimal external components and full functionality make this EL7563C ideal for desktop and portable applications. The EL7563C is specified for operation over the full -40°C to +85°C temperature range. Typical Application Diagram (EL7563CM) ...
Page 2
... EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Absolute Maximum Ratings Supply Voltage between and GND Voltage LX Input Voltage V Voltage HI Important Note: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the ...
Page 3
... PGND 4.7µH 8 PGND PGND VIN VIN STP PGND 16 14 STN PGND 15 EL7563CRE 3 EL7563C Min Typ Max Unit 100 115 125 kHz 25 ns 0.5 V/ 150 0.22µ 0.1µF V OUT 2.5V C10 4A 2.2nF R2 1.54k ...
Page 4
... EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Pin Descriptions Pin Number Pin Name 1 VREF Bandgap reference bypass capacitor; typically 0.1µF to SGND 2 SGND Control circuit negative supply or signal ground 3 COSC Oscillator timing capacitor (see performance curves) 4 VDD Control circuit positive supply; normally connected to VIN through an RC filter ...
Page 5
... Load Regulation V =2.5V O 2.505 V =1.8V O 2.5 2.495 2.49 2.485 V =1V O 2.48 2.475 2.47 2.465 3 3 Junction Temperature REF 1.27 1.268 1.266 1.264 1.262 1.26 1.258 1.256 3.5 3.6 -50 -10 5 EL7563C O V =3V IN =3.3V V =3. 1.5 2 2.5 3 3.5 4 Load Current I ( =3. =3. =3V IN 1.5 2 2.5 3 3.5 4 Load Current I ( 110 150 Junction Temperature (° ...
Page 6
... EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Typical Performance Curves *Note: The 28-Pin HTSSOP Package Offers Improved Performance Switching Frequency vs C OSC 1000 900 800 700 600 500 400 300 200 100 100 200 300 400 500 600 700 C (pF) OSC * vs Copper Area ...
Page 7
... Typical Performance Curves Power-Down V =3.3V, V =1.8V Disable V =3.3V, V =1. Monolithic 4 Amp DC:DC Step-down Regulator Enable V =3.3V, V =1. Short-Circuit Protection V =3.3V, V =1.8V, I =4A to short EL7563C ...
Page 8
... EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Block Diagram VTJ Junction Temperature 2.2nF Controller Supply 22 VDD 3.3V 0.22µF EN STP Power Tracking STN SGND FB 0.1µF 390pF VREF COSC Voltage VDRV Oscillator Reference VHI VIN Power FET PWM Drivers Controller Power FET PGND Current Sense VREF ...
Page 9
... Applications Information Circuit Description General The EL7563C is a fixed frequency, current mode con- trolled DC:DC converter with integrated N-channel power MOSFETs and a high precision reference. The device incorporates all the active circuitry required to implement a cost effective, user-programmable 4A syn- chronous step-down regulator suitable for use in DSP core power supplies ...
Page 10
... FET, via the VHI pin. A value of 0.22µF for CVHI is recommended. Reference A 1.5% temperature compensated bandgap reference is integrated in the EL7563C. The external VREF capaci- tor acts as the dominant pole of the amplifier and can be increased in size to maximize transient noise rejection. A value of 0.1µF is recommended. ...
Page 11
... HI output forces the PWM control- ler to skip switching cycle. 1. Linear Tracking In this application always the case that the lower voltage supply V Please see Figure 2 below OUT V P Figure 2. Linear Power Tracking 11 EL7563C tracks the higher output supply TIME . ...
Page 12
... EL7563C STP 9 + STN - EL7563C 8 STP 9 + STN - 10 However, due to the superimpose of V choice of R and R A relationship: reaches Where 0.5 is for noise immunity. See Figure 3 below ...
Page 13
... EL7563C EL7563C Monolithic 4 Amp DC:DC Step-down Regulator . Figure 4. Offset Tracking 13 EL7563C TIME ...
Page 14
... External Soft Start An external soft start can be combined with auxilliary supply tracking to provide desired soft start other than internally preset soft start (Figure 5). The appropriate start-up time is EL7563C STP STN - Figure 5. External Soft Start ...
Page 15
... A capacitor can be added to the EN pin to delay the con- verter start-up (Figure 6) by utilizing the pull-up current. The delay time is approximately 1200 EL7563C 8 STP 9 + STN - 10 Monolithic 4 Amp DC:DC Step-down Regulator OUT Figure 6. Start-up Delay 15 EL7563C TIME ...
Page 16
... The heat of the chip is mainly dissipated through the PGND pins. Maximizing the copper area around these pins is preferable. In addition, a solid ground plane is always helpful for the EMI performance. The demo board is a good example of layout based on these principles. Please refer to the EL7563C Applica- tion Brief for the layout. 16 ...
Page 17
... Package Outline Drawing NOTE: The package drawing shown here may not be the latest version. For the latest revision, please refer to the Elan- tec website at http://www.elantec.com/pages/package_outline.html Monolithic 4 Amp DC:DC Step-down Regulator 17 EL7563C ...
Page 18
... EL7563C Monolithic 4 Amp DC:DC Step-down Regulator General Disclaimer Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir- cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement ...