IR3313PBF International Rectifier, IR3313PBF Datasheet

IC SWITCH HI-SIDE PROG TO-220FL

IR3313PBF

Manufacturer Part Number
IR3313PBF
Description
IC SWITCH HI-SIDE PROG TO-220FL
Manufacturer
International Rectifier
Type
High Sider
Datasheets

Specifications of IR3313PBF

Input Type
Non-Inverting
Number Of Outputs
1
On-state Resistance
5.5 mOhm
Current - Output / Channel
23A
Current - Peak Output
100A
Voltage - Supply
6 V ~ 32 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Switch Type
High Side
Power Switch Family
IR3313
Power Switch On Resistance
6mOhm
Output Current
23A
Mounting
Through Hole
Package Type
TO-220AB
Operating Temperature (min)
-40C
Operating Temperature (max)
150C
Operating Temperature Classification
Automotive
Pin Count
5 +Tab
Power Dissipation
2W
Power Load Switch Type
High Side
Input Voltage
32V
Current Limit
23A
On State Resistance
0.006ohm
Thermal Protection
Yes
On / Enable Input Polarity
Active High
Power Dissipation Pd
2W
No. Of Outputs
1
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IR3313PBF
Manufacturer:
IR
Quantity:
12 500
Features
Description
The IR3313(S)PbF is a fully protected 4 terminals high
side switch. The input signal is referenced to Vcc. When
the input voltage Vcc - Vin is higher than the specified
threshold, the output power Mosfet is turned on. When the
Vcc - Vin is lower than the specified Vil threshold, the
output Mosfet is turned off. A current proportional to the
power Mosfet current is sourced to the Ifb pin. Over
current shutdown occurs when Vst-Vin > 4.5V. The current
shutdown threshold is adjusted by selecting the proper
RIfb. Either over current and over temperature latches off
the switch. The device is reset by pulling the input pin
high. Other integrated protections (ESD, reverse battery,
active clamp) make the switch very rugged in automotive
environment.
Typical Connection
www.irf.com
Off
Load current feedback
Programmable over current shutdown
Active clamp
ESD protection
Input referenced to Vcc
Over temperature shutdown
Reverse battery protection
PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH
Current feeback
On
Input
10k
IN
Ifb
Rifb
Ground
Logic
IR3313
Ground
Power
Product Summary
Packages
Vcc
Out
Rds(on)
Vcc op.
Current Ratio
Prog. Ishutdown
Vclamp
TO-220
IR3313
Load
Battery
Data Sheet No. PD60288_D
IR3313(S)PbF
Pin 4 and 5 fused
7 m max.
IR3313S
6 to 32V
D²Pak
10 to 90A
8800
40V
1

Related parts for IR3313PBF

IR3313PBF Summary of contents

Page 1

PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH Features  Load current feedback  Programmable over current shutdown  Active clamp  ESD protection  Input referenced to Vcc  Over temperature shutdown  Reverse battery protection Description The IR3313(S)PbF is a ...

Page 2

Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Vcc lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Vcc-Vin Maximum Vcc voltage Vcc-Vin cont. Maximum continuous Vcc ...

Page 3

Protection Characteristics Tj=25°C, Rifb=500 to 3.5k Symbol Parameter Vifb-Vin@Isd Over-current shutdown threshold Tsd Over temperature threshold OV Over voltage protection (not latched) Isdf Fixed over current shutdown Isd_1k Programmable over current shutdown 1k Treset Time to reset protection Min. pulse ...

Page 4

Current Sense Characteristics Symbol Parameter Ratio I Load/Iifb current ratio Ratio_TC I Load/Iifb variation aver temperature(6) Offset Load current diagnostic offset Trst Ifb response time (low signal) Functional Block Diagram All values are typical 43V 3mA + - 4.7V - ...

Page 5

Lead Assignments 3- Vcc TO220 Vcc-Vin Vih Vil Vhyst Vcc IN IR3313 Iin Ifb Out Ifb Figure 1 – Voltages and current definitions www.irf.com Ifb 3- Vcc (tab) 4- Out(TO220 NC) 5- ...

Page 6

T clamp Vin Iout Vcc V out Vcc - V clamp See Application Notes to evaluate power dissipation Figure 3 – Active clamp waveforms Vcc-Vin Over-current shutdown Iout Tj www.irf.com Vcc-Vin t < T reset t > T reset Wait ...

Page 7

All curves are typical characteristics. Operation in hatched areas is not recommended. Tj=25°C, Rifb=500ohm, Vcc=14V (unless otherwise specified Vcc-Vin, supply voltage (V) Figure 6 – Icc (mA) Vs Vcc-Vin ...

Page 8

With calibration 16 14 Spec. Max load, load current (A) Figure 10 – Error (+/- load ( -50 0 Tamb., ...

Page 9

Protection response time (s) Figure 14 – Ids (A) Vs over temperature protection response time (s)/ Rth=60°C/W www.irf.com Tamb=25°C Tamb=100°C 1.E+01 1.E+02 1.E+03 IR3313(S)PbF 100 50°C/W free air 10 5°C/W 1 0.1 0.01 1E-4 1E-3 1E-2 ...

Page 10

Case Outline 5 Leads - D2PAK – Automotive Q100 PbF MSL1 qualified www.irf.com IR3313(S)PbF 10 ...

Page 11

Tape & Reel 5 Lead - D2PAK (SMD220) www.irf.com IR3313(S)PbF 11 ...

Page 12

Case Outline 5 Leads – TO220 – Automotive Q100 PbF qualified IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 This product has been designed and qualified for the Automotive [Q100] market. www.irf.com IR3313(S)PbF Data and ...

Related keywords